Models > 11060712990 > Instructions

11060712990 Kenmore Dryer - Instructions

All installation instructions for 11060712990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060712990
1,351-1,365 of 1,479
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Multi Rib Belt - 92 - 1/4"

  • Customer: Michael from San Juan Capistrano CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Exactly as described by the video.

Tub would not turn

  • Customer: Lynn from Adel GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and performed as instructed- Could not have been easier- Great site with Great information

Broken dryer belt.

  • Customer: anthony from redmond OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I came home from work to notice the dryer singing a different tune than usual. I opened the door and noticed that the tub wasnt turning. I popped the top of the dryer up to find a disentigrated belt. Fired up the computer and in a few minutes had ordered the $8 ($15 including shipping) replacement belt. 3 days later took the shopvac and cleaned up the lint and broken belt pieces. Installed the new belt and was back in business with my 8 year old dryer. ** The only complaint comes from my wife who got her hopes up for a new front load washer and dryer** Thanks PartSelect for saving my wallet in more than one way!

dryer ran 5-10min,then stopped until it cooled off

  • Customer: Leonard from Bayside NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Remove two screws on top holding the filter frame.Use flat screwdriver to snap top at front off front panel.Swing top up and secure it against wall or tie in place. Remove screws holding front panel and kick panel to side panels.Did'nt remove back panel.Remove drive belt from pully wheel and then use belt to lift out drum.Use open end wrench on motor pully at rear and I used a socket set on the front of motor,Push down on wrench,counter clockwise,and hold the front pully from moving mine came right off. My dryer is over 10 yrs so the electric conection was changed but the instruction sheet explained how to change the wires,just follow the wire color,easy.

Belt Broke

  • Customer: Dann from Granville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.

Drum does not rotate, motor runs and it heats

  • Customer: Barry from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Opened the top. (UN-plugged it first) by prying between top and front of machine.
2. Disconnected the door switch
3. Removed two screws one each on top corners of front
4. Pulled top of front cover forward and lifted up to remove.
5. The drum will fallout if not careful, good time to remove drum to clean dust from inside machine.
6. With drum in place slide new belt, skinny side down around drum, to about halve way back.
7. While supporting drum reach back to the motor area, should be on right side facing front of machine. There you will find the belt idler/tension assembly.
8. Thread the belt through the assembly and around the motor drive pulley.
9. Ensure the tensioning assembly is firmly in the slots on floor of machine.
10. Reassemble housing in reverse order. took about 45 minutes

Broken Belt

  • Customer: ANDREW from MOUNT UNION PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Fast shipping. Part arrived the next day!

Ribbed belt broke

  • Customer: richard from satellite beach FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions you supplied. All went well. The short movie that you supplied was fine but the only tricky part which included placing the belt over the idler wheel was not well done in that the repairman's arm covered the work area. Delivery time was excellent.

Motor required replacement

  • Customer: James from Port Washington NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the You Tube video on this site. The only issue is there is a plastic fitting that I seriously damaged trying to remove the motor from the blower. You have to hold the plastic fiting stationary while turning the nut on the other end of the motor. If you try to rotate the plastic fitting you'll destroy it as I did. I got it loose by squeezing the plastic fitting with a large pair of channel lock pliers and then rotating the nut.

Broken dryer belt

  • Customer: MARY from CINCINNATI OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I was able to take apart the dryer myself and get old belt out, then my son helped me remove the drum and put new belt on. Well worth fixing; it works great again and the part with shipping and handling was only $17.00! better then price of new dryer!!!Thanks, Mary ( Cincinnati)

Drum stopped spinning

  • Customer: Anthony from Oak Ridge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
You pop the top of the dryer. Remove to hex screws which allow you to remove the front panel. Next you pull the drum off, snack the belt around the drum, motor and tension pulley and reverse the steps. The hardest part is getting the drum back in place without knocking the belt off the motor.

Dryer was not heating up

  • Customer: Kathy from Munhall PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After watching the very helpful videos, we replaced the fuse and belt. The belt ended up breaking and shredding because we did not put the ribbed side down... The dryer heated up for about 2 minutes then was cold again. I had so much clothes needing washed/dried, that we decided to buy a new one. We did give the dryer to someone who was going to try to fix it for themself.

Belt on dryer drum broke

  • Customer: Thomas from Buffalo NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair on replacing the clothes dryer belt went great. Not only did Part Select send me the correct belt at a great price .. the helpful hints that other people gave was most helpful. The only glitch was when I was pushing the tensioner wheel to get the belt around the pulley it slipped and the spring came off. The instructions/tip of taking the drum out and how to replace it came in handy when I had to get the spring back into place. The belt finally went on but there was a slight twist in it by the tensioner wheel. Again the tip I got with my e-mail helped as I manually turned the drum and was able to right the belt. Kudos to the tips I received and the confidence I could do the job myself!!!!

Broken belt.

  • Customer: Cynthia from Mayfield NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched Youtube video first then followed directions included with belt. Very simple and easy to follow.

Belt broke on dryer, drum therefore wouldn't tumble

  • Customer: Elaine from North Berwick ME
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Had a hard time at first trying to figure out how to place the pulley wheel that you place the belt around, it holds it in place so to speak, was getting very frustrated came upstairs went on line to your web site and lo & behold there was a video on how to do it, I watched that video (thanks Steve) and went back down cellar and had the belt on in less than 5 mins and everything is working fine. Thanks for all your help Dan
All Instructions for the 11060712990
1,351-1,365 of 1,479