Models > 11060622990 > Instructions

11060622990 Kenmore Dryer - Instructions

All installation instructions for 11060622990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060622990
1,351-1,365 of 1,445
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Tab of door switch broke off

  • Customer: Michael from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Had to buy the entire new unit, but followed the video, took notes and it was a piece of cake!

Dryer would not stop when door would open and light would not light

  • Customer: Donald from Scranton PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as video describe

Switch broke

  • Customer: David from Lynn Haven FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Folowed the tips that I got with the part and on the site. Could not have been an easier way to save about $150 in a pro service call and marked up price for their part. Very easy install. Drying working as it should. Now, I just learned the washer control mechanism is about to go bad, so ill be back for that part too. Thanks.

Drum still turns when door open and light does not come on.

  • Customer: Leroy from New Orleans LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1.Unplugged power cord to Dryer. 2.Removed Dryer vent screen, unscrewed two screws located in dryer vent.3.Pried open top of dryer using putty knife. 4.Propped up top of dryer using 6 inch piece of wood resting on drum of dryer. 5.Removed screw holding door switch.6.Removed door switch from harness using putty Knife to pry apart connection. 7. Installed new door switch to harness and re-installed. 8.Removed wood used to prop open top, closed top, re-installed all screws, dryer vent and plugged dryer back up.

Dryer stayed on when door opened/would not start

  • Customer: Karen from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer started staying on when I opened the door to check the clothes, which I adapted to. Over the next few weeks, the dryer would not start at all. The website was very helpful in determining the possible parts needed to make the repair. The video shown was spot on and very helpful with its instructions on access to the part and replacing the part. The most time it took for me was cleaning behind the dryer and trying to remove the existing switch. I kept trying to squeeze the tabs on each side to get it past the tab and that wasnt working for me. Finally I took a small flat screwdriver and gently lifted the plastic on the switch up over the tab and that allowed me to pull and remove the switch easily. The whole time from start to finish for me was 45 minutes. Not bad for a 50 year old lady :) I have to say that this whole process has giving me alot of confidence in making basic appiance repairs. I have my partsselect.com magnet proudly displayed on my dryer and will not hesitate to use them again in the future.

door switch broke off

  • Customer: Richard from Murray UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 2 screws by the lint collector, lifted top and disconnected the door switch, removed old switch and replaced it with the new one, screwed it back in and reconnected it, closed lid and reattached the screws by the lint collector-done!

dryer stopped working

  • Customer: S from Honolulu AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got the info from PartSelect that the door switch might be the problem, which confirmed my suspicions (as the dryer had lately been failing to stop when the door was opened), ordered the door switch (which had arrived in good time, BTW), installed the part after figuring out that the top panel of the dryer is fixed in place with the two screws accessible in the filter door opening. Put it all back together (that is, re-fixed the top panel with the two screws I'd had to remove), plugged it in, fired it up, ascertained that the repair had been successful, expressed appropriate thankfulness to God for an easier-than-imagined repair, cracked a celebratory brewed product, and commenced working through a hefty few piles of neglected laundry.

Dryer not turning on or not staying on

  • Customer: Reggie from Lynchburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Followed instructions on the installation video you had on line. Really easy and fixed the problem.

Dryer would not start

  • Customer: Patrick from East Bridgewater MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The video instructions here were exact and very clear. I replaced the door switch but that did not fix the issue. I used the instant repair man tool and found that the next most likely part to have an issue was a the thermal fuse. After replacing that part which took 10 minutes... It works! My part was shipped to my home very very quickly. totally worth it.

The Door switch on my dryer broke which stopped the dryer from turning on.

  • Customer: nancy from Colonia NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video. Removed two screws by the lint filter, lifted up the 2 sides to the top of the dyer, removed the two screws by the door switch. It was that easy. The hard part came when I tried to remove the old switch that took the most time. I used the butter knife, since it was very flat I was able to lift it off. Put in the new switch, put all the parts back together again and it worked just fine. Thank you, PartSelect, I will come to you first. You saved me at least $150.00....

the door switch wire went bad and the dryer would not start

  • Customer: Martha from Deltona FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the guy repair it on the video provided when i searched for the part. He made it look very easy and he explained it step by step. I ordered the part from partselect.com and 12 hours later i had the part in my hand and proceeded to replace it. Instructions and delivery were amazing. Thanks to all at partselect!!!

Dryer was here when we moved in. The light never worked and the dryer would not stop when you opened the door. Eventually the dryer would not turn on at all.

  • Customer: Peter from Charlotte NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the youtube video and it was very helpful. The repair was very simple. Just remove the lint trap, then the two screws under there, then use the putty knife to pop the two front corner clips. Disconnect power before you do anything of course..... once its all disconnected, you will see the switch. 2 Screws hold it in and then it unclips. Reverse to reassemble.

Door switch failure prevented drier operation. This could be confirmed by the fact that the interior light was also not working.

  • Customer: DONALD from FORT LAUDERDALE FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled drier away from wall six inches. Pulled the plug for the drier power cord out of the wall socket and hooked it up so it would not fall down behind the drier, thereby knocking loose the vent hose. Removed two screws from front of filter housing opening (right of drier top). Lifted up drier top (lid) from the front and secured it in the up position using a stout strap with hooks on both ends. A prop is not a safe way to hold up the lid. Lid is held down only with mildly stubborn friction catches. Door switch was seen looking down along the inside of the drier front on the right side. There was nothing else in that area to cause confusion. Opened drier door and removed two vertical screws that secure the door switch to the front panel of the drier. Lifted the now-free switch and unplugged it from the wire socket. Plugged in replacement switch securely. Replaced the screws securing the new switch to the front panel. Checked that all wiring was back in place and clear of the drier drum. Lowered the drier top. Replaced the screws into the filter housing. Plugged the drier in. Tested the operation of the drier. Checked out spouse's smile. IMPORTANT - Checked that drier vent hose was still firmly in place. Pushed it back in place.

SWITCH BROKEN NOT ALLOWING DOOR TO START DEVICE

  • Customer: bill from ashland KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I used the instruction vedio on this web site. Instruction from this vedio showed; was very helpful and for a first timer took less than twenty minutes.

dry would not run or stop after the door was open

  • Customer: Francis from Cocoa FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Un plug the Elect. The two screws that hold the lent screen in place and the top. I took them out and I used a putty knife to open the top of the dry. un plug the switch And take out the two screws under the switch. That was all too it. Just like the instructor said .
All Instructions for the 11060622990
1,351-1,365 of 1,445