Models > 11060602990 > Instructions

11060602990 Kenmore Dryer - Instructions

All installation instructions for 11060602990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060602990
1,771-1,785 of 1,881
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer ran but no heat

  • Customer: Nels from South Haven MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
turn off elec./disconnect at recep.- remove vent pipe- remove back of dryer- remove each part and re-install new part- relaced thermal cut-off, thermostat, fuse, and heat element...time about 30 min. also vacuumed dryer and vent pipe-time less than 15 min.- parts arrived day after they were ordered.

Dryer took a long time to dry clothes and towels,

  • Customer: Antony from Boone NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I viewed a number of vidieos on the Webb to determine the possible problems. The vidieos explained and demonstrated how to test the parts that could have been causing the problems. I tested the parts described in the vidieos and the ones I was able to test showed that they were not defective. I was unable to test the Cycling Thermostat and the High Limit Thermostat to my satisfaction so I ordered the two parts and installed them as demonstrated on the vidieos. The dryer works as if it was a new one. I am a very satisfied customer and will definitely purchase my parts from partselect.com in the future.

Dryer keeps running without drying

  • Customer: Charles from Summit MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched installation video (very hepfull),used battery driver (faster)to remove back (9 screws). Used nutdriver to remove screw holding old part, removed part. Changer wires one at a time to prevent wrong placement of wire. Parts ordered were correct and arrived in 2-3 days. Thanks PartSelect. Very easy install, video made me an "instant repairman."

Belt & clip where both broken

  • Customer: Amy from Seagrove NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

Squeaky Idler Pulley

  • Customer: Mitchell A. from Hampton NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

Broken belt and bent idler pulley

  • Customer: Mollie from Walterboro SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First unplug the unit. Take the lint filter out and remove the two Phillips-head screws at the edge of the opening. Then using the putty knife to unlatch the top panel of the dryer, insert it into the seam on the front about 3" from each side. When you feel the knife up-against the latch, apply a little inward pressure with the knife and pull up on the top panel. When you release both sides the panel, it will lift up and back against the wall(secure it so it doesn't fall forward while you are doing this repair). Looking down on the right-front corner you will find a connection for the door switch, Dis-connect it. Just below that connection, on the inside, is a 5/16" screw that holds the front panel on, take that one and another one just like it on the left side, out and the front will fall forward about an inch and then you will lift up on the panel while holding drum in place. Inspect the clips that hold the bottom of the panel on and be aware how the panel attaches to them. Try to keep the drum in place and set the front panel off to the side so you can easily grab it to put it back on. Looking under the drum remove the belt and idler pulley. The pulley is usually not in the position it should be in, it likes to fall over when it has no belt pressure on it. Hopefully you had already unpackaged the new belt and straightened it out. Loop the belt over the drum, rib side to the drum, and move it to where the old belt had been riding on the drum. Back under the drum, you should hold it in place with your shoulder, with idler pulley in hand-- install the idler pulley. There's probable a clean spot where the old one was and the humpback should point to the right side of the dryer. With right hand steadying the idler pulley, the left hand should pinch the belt together and feed it under the wheel and pull it out and hook it on the motor pulley. It may seem to be a tight fit but once its on you should be able grab the outside edge of the drum and slowly turn it without hearing any scraping noises. Double check that the belt isn't twisted. Before putting the front panel back on or if you had to take the drum out, make sure the felt seal on the back edge of the drum is not folded inward. the wheels that the drum roll on must be in the groove. Carefully reach to the back to check that they are in the groove of the drum. If everything seems to be in place, hold the drum with one hand and grab the front panel with other. Place the bottom of the panel against the unit and lift up about an inch and place the square holes at the bottom of the panel on the clips on the unit, it may take a couple of tries, then lean the panel forward making sure the drum goes around the felt seal on the panel. Once the panel is against the unit , install the two 5/16 screws securing the front panel to the unit. Turn the drum by hand to make sure drum was installed properly. Reconnect door switch. Lower top panel and push down to secure it. Install the two Phillips head screws at the edge of where the lint screen goes, install lent screen and plug the unit back into the wall socket.

Door switch hadn't been working for a while and when the belt broke decided to make it right.

  • Customer: Martin from Saylorsburg PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front and replaced belt,idler pulley and door switch. Was an easy repair.

drum not turning

  • Customer: Tony from Greenville IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a video on utube and realized how easy this looked, took my dryer apart to see the belt broken in half and the idler pulley in pieces. Found Partselect on the internet and ordered my parts. Partselect was awsome, website was easy to navigate, ordered my parts and they were at my house the very next day and were the correct parts. Cleaned all the lint and dust out of the inside of my machine, installed new parts and put it back together. Works great and is still running strong. A service call, plus parts (with thier mark up) could have easily been $150.00 - $200.00 dollars. this repair was complete in about an hour and only cost me $37.50

Lould nosie from Drum Whells

  • Customer: FRANCIS from PHILADELPHIA PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

loud squealing when running

  • Customer: Michael from Easton MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video provided by PartSelect. It pretty much went exactly like the video said it would. I was pretty sure the belt or idler pully must be the culprit, but I didn't even know how to open the thing up until I saw your video. I would likely still be putting up with the squealing without that video. Now the dryer is nice and quiet. -Mike

Dryer would run for approximately 8 mins, then shut off by itself. After about 20 mins, dryer would restart but stop on it's own within 8-10 mins. Motor was also noisy when it ran.

  • Customer: Terrence from Hotsprings AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Unplugged dryer, removed 2 screws under filter lid, removed filter, removed access panel on back of machine, removed blower motor housing, vacuumed all dust and debris from rear of dryer, turned dryer around and opened top of dryer using a small screwdriver to release the clips approximately 2" from either end, then securing top from falling by using bailing wire to hold it in place, disconnected door switch wiring harness, removed 2- 5/16 screws retaining front panel and removed front panel from dryer, removed drum from dryer, removed idler pulley from bottom of cabinet noting position of drum belt, vacuumed dust and debris from bottom of cabinet and around old motor, removed motor retaining clips rotated motor and removed wiring harness from motor. I then attempted to remove the blower wheel from the old motor and here is where the problem began. If your dryer has the original motor in it, or the motor has never been changed in it to the best of your knowledge, go ahead and order a new blower wheel with your other parts, because you will not get the old one off without destroying it. (this cost me several days to complete the repair). Do not use channel locks or vice grips to attach to the front pulley to remove or install the blower wheel... use 2 medium sized crescent (adjustable) wrenches otherwise the pulley will be damaged and you will have a lot of filing to do to repair it. (If you need to reuse the pulley. I did not as my motor and pulley was an exact replacement). I got the blower wheel off of the old motor by using a chisel and a hammer and cutting a hole around the attachment point on the motor shaft from the rear of the dryer. After this, the job was pretty easy. I put the new motor in the motor housing, put a crescent wrench on the pulley on the front of the new motor, then screwed the new blower wheel onto the motor from the back of the dryer. (remember, the blower wheel has left handed threads, so to install it you have to turn the pulley on the motor to the LEFT to thread it into the wheel.) After the blower wheel is installed and hand tight, use 2 crescent wrenches to tighten down on motor, (1 on the blower wheel hub where it is square, and 1 on the front pulley) rotate the motor down to the correct position for the wiring loom, (you want the wires to rest on the bottom of the cabinet when the job is complete)., then reinstall the motor retaining clips and attach wiring harness. At this point I installed new drum rollers, reinstalled the drum with a new drum belt, and replaced the idler pulley with a new one. (push the drum counter clockwise by hand a few times to center the drum belt and to make sure that the drum is on the drum rollers correctly). The front panel is now reinstalled being careful to make sure the clips on the cabinet engage the holes in the panel. Push back on the drum slightly and reinstall the 2- 5/16 screws to hold the front panel to the cabinet, then reattach the wiring harness for the door switch. Remove the bailing wire and close the lid. The blower wheel housing is then reinstalled, then reinstall the rear access panel. Reinstall the filter and the 2 screws under the filter lid. Plug in the dryer and your repair is complete. When a motor replacement is required, you are better off replacing the motor, blower wheel, drum rollers, drum belt, and idler pulley. I did and my dryer sounds and performs like a new one. My wife is absolutely delighted. I spent approximately $180.00 on the total repair while a new dryer would have cost me $600.00 + tax.

tumbler would not turn

  • Customer: LORRIE from ARNOLD PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the video directions exactly as instructed and I had no problem doing the repair myself. And if I can do it being a woman with no help you can do it. Easy peasy~

my dryer stopped tumbling

  • Customer: joann from woonsocket RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me

Sqealing noise and extended drying time

  • Customer: Gregory from Casa Grande AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed online youtube directiond to dissassemble dryer cabinet. Everything is readily accessible and belt and idler are easily installed. Comments from others express frustration at the instability of the idler pulley bracket. The key is to keep seating pressure on bracket until the belt is installed at which time the belt supplies continuous pressure to seat the bracket. The bracket is very stable so long as moderate force is applied to hold the brackett in the seat. The belt install is counter intuitive in that the ribbed side of the belt is installed in contact with the drum instead of the flat side. The readon for this is so the belt ribs seat in the grooves of the motor pully and provide greater friction. Flat side of the belt on the drum places the flat belt on the grooved pulley with much reduced contact area.

Dryer had become REALLY noisy.

  • Customer: William from Dallas TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The PartsSelect video was great. I'm not sure I would have figured out the trick for opening up this dryer without it. After that the main problem was getting goop off of the drum support roller spindles. This took lots of solvent and elbow grease. I think this was the main source of noise. The oil had turned to something like partly dried glue. They were very hard to turn. The belt was intact but badly cracked. The idler probably could have been oiled and reused but I already had the part so I replaced it. Everything went just like the video. The dryer now hums along like a new one!
All Instructions for the 11060602990
1,771-1,785 of 1,881