11060232002 Kenmore Dryer - Instructions

My 40-ish year old Whirlpool dryer needed its lint filter replaced. You guys had the replacement! Fast shipping and even faster switching out the filter. Thank you PartSelect.

I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Door latch or kill switch. Rewarding experience to fix on own.

Unplug the dryer, remove hot air duct. Remove metal dryer back to access thermostat using a nut driver. Unscrew one screw holding on thermostat, detach 4 wires, and replace with new unit, attaching 4 wires to new unit. Then reverse process to button up the dryer. Great how-to video on your site helped a lot!

after process of elimination ,figured had to be cut off switch followed simple instructions also watched your video..simple repair up and working again approx. 30 min. once i had kit. thanx 4 the help MIKE

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

Unplug unit / removed back cover / went down , locating both parts to be replaced / simple one screw removal from each part / thermal fuse , one wire @ a time , reinstalled . / Cycling thermostat , 4 wires. Did one wire @ a time , reinstalled. / Putted back cover back on , plugged dryier back up, turned it on to run. To check for heat / yes, ran good as new. Later that day some more running , with damp clothes in it. Did it's job , dry.

Took the back off of the dryer, looked on "parts select" found what I thought might be the problem. Got the parts the next day. Put on new thermal fuse, then put on cycling thermostat. Wasn't sure which it needed, so put both on. Put the back of the dryer on hooked the gas up, hooked up to electric, & turned the dryer on. Back in business, everything works, dryer works as if nothing was wrong. Thanks to "parts select" saved me a repair bill.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

first I unplugged the dryer. Then I removed the back of the dryer with a 1/4" nut driver. with the back off using the same 1/4" nut driver I removed the one screw that holds the cycling t-stat slowly remove the t-stat and take one wire off at a time and plug it onto the new t-stat once all wires are replaced. place the t-stat back in and secure with the screw. Then put the back of the dryer back on. put the dryer vent hose back on. plug in and away you go. repair done. If that doesn't fix it. Then the next step is probably to check the gas valve coils. That is a little more difficult repair but not to hard.

Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!