Models > 11060202990 > Instructions

11060202990 Kenmore Dryer - Instructions

All installation instructions for 11060202990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060202990
1,186-1,200 of 1,277
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken belt

  • Customer: Rick from Emporium, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the instructions that came with belt everthing went just fine.

Belt popped

  • Customer: Wade from Labadieville, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
2 screws at lint tray 2 screws on back pick up top 2 screws in front under top lid separate front from drum slip in new belt screw front back to top route around tension pully put other 4 screws in complete so dry something

Broken belt

  • Customer: Alex Peden/ Angel from Jamestown, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Popped top up Took front panel screws out. Looked for other damage. Put belt around the tumbler and got it hooked up. Grew an extra set of hands and re assembled front the checkd seals to make sure they where on and put top back down... Process is a pain in the butt i reccomend socket set channel lock pliers and a cold beverage or two

The dryer belt broke.

  • Customer: Bill from Cooper City, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the attached video that was with the belt I ordered and it took less time to do the repair, then it did to watch the video. The video was very helpful.

Motor hum on start-up

  • Customer: GREG from BLAIRSTOWN, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Trouble shot to failed motor. Ordered motor and new drive belt. The hardest part is figuring out how the dryer dis-assembles. Follow Parts Select on-line instructions. Also, several good instructional videos on You Tube! My recommendation is to order a new "blower wheel" when changing motor on a gas fired dryer. The heat combined with age bonds the blower fan to motor shaft. It had to be broken off in pieces to remove motor.

Dryer Belt Popped

  • Customer: Lawrence from Washington, DC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The dryer belt was delivered promply, afterwards I lifted the top of the dryer and unscrewed the front panel, so it would lower. Then I watch a 5 minute video and it clearly demonstrated how to install the belt. This was my first time, so it took about 30 minutes.

broken belt

  • Customer: Robert from Winchester, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the video was very helpful

Broken Belt

  • Customer: Patricia from Durham, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
PartSelect sent the exact right part, and very quickly! YouTube showed me how to install it. The only hard part was the bulkiness of the drum, which is why I marked "a bit difficult" for the repair.

Drive belt broke

  • Customer: Robert from Port Arthur, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove Filter and (2) phillip screws. Use common screw driver to pry top from cabinet. Fold top back. disconnect door switch and removed (2) screws holding front of cabinet and lift frong slightly to remove from cabinet. Remove broken belt and discard. check rollers for freedom and placed drum on rollers. guided belt through idler and around motor pulley. lift front and placed on lower hooks. Lift drum and installed (2) screws that holds front of cabinet to main cabinet. connect door switch and check drum for freedom of turn. turn drum several times to get belt to center. Closed top and replaced (2) screws that hold filter door in place. Install filter and test run dryer. Completed job in about 38 minutes.

Belt broken & toe panel was loose

  • Customer: Jim Ten from Sheboygan, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions supplied with the belt. I've changed the belt before so was familiar with the repair. The toe panel clips for my model had changed so what was supplied was different than the originals. Although they, too, came with instructions, they did not fit my appliance. They were inexpensive so I scrapped them and used some self-adhesive Velcro fasteners I had in a junk box.

dryer belt broke

  • Customer: LAWRENCE from BANDERA, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
belt # 346995. part was delivered quickly. Part fit perfect, no problem. there was a video on youtube how to replace it. It took about 25 minutes from start to finish to install. works like a new one. Thanks partselect.

Broken Dryer belt

  • Customer: Glenn from Waterford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I follow the instructions from the video sent to me with the email to tell me my new belt was shipped. Made the whole job go a easy as could be. Parts Select made fixing my dryer so simple and I also got the belt within 2 days. I recommend buying parts only from you! Glenn

Broken belt

  • Customer: Christopher from Skillman, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Used PartSelect instructions for routing belt & a customer's valuable guidance.

Broken Belt Tub wouldn't turn

  • Customer: Leslie from augusta, WV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

Broken Dryer Belt

  • Customer: Andrew from Avoca, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Must remove 2 screws in the lint screen port anchoring the top of the dryer. Next the front panel of the dryer is removed from the machine by pulling up with a putty knife disassembling the clip holding the front in place. 2 more screws are then removed holding front panel of the dryer. The doors sensor switch is then removed freeing the front panel to be removed. At this point after the front panel is off and the top of the dryer lifts in an upwards position and you can now see the tub and the broken belt. The belt has to be reinserted around the tub into the pulley assembly before being pulled onto the motor. The pulley lifts upward towards the tub if it was put on correctly. It has to be placed underneath the pulley in order to have tension put on the belt firming the connection between the tub and motor. To reassemble just reverse what you have taken off in that order. Their is a DYI video which shows the process perfectly. Have a good one !
All Instructions for the 11060202990
1,186-1,200 of 1,277