Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11060094991 > Instructions

11060094991 Kenmore Dryer - Instructions

All installation instructions for 11060094991 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060094991
61-75 of 412
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

When using the dryer the cycle would stop and display E1 as the reason

  • Customer: Joyce from Holbrook, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.

no heat

  • Customer: Hal from Edgewater, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 7 people found this instruction helpful
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid out old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more

Dryer would not turn on

  • Customer: Pam from Chandler, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 10 people found this instruction helpful
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!

Dryer working, but not heating

  • Customer: Amy from Birmingham, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set, Wrench set
  • 8 of 10 people found this instruction helpful
Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.

The old door catch failed. Clothes won't dry with door open !

  • Customer: Theresa from Norfolk, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 7 people found this instruction helpful
Old door catch came out, new one slipped in. All works great.

Wouldn't heat

  • Customer: Lorraine from Elk Grove, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 8 of 10 people found this instruction helpful
My husband said it was very easy and quick. We will recomend your site for sure.

Not heating

  • Customer: Manuel from Key Biscayne, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!

my dryer would not heat up any longer

  • Customer: Chris from Great Bend, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screws back in and fastend the front back on and were in bussiness!

Dryer wouldn't run

  • Customer: Edward from Richlands, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one. Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!

Repair took about five minutes and saved approximately $70!

Dryer was taking twice as long to dry as it used to.

  • Customer: Glenn from East Brunswick, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Took of the back cover, and removed the vent connecting the blower motor to the drum. It was completly full of lint, so cleaned it out completly, and tried the dryer again. The heater element was still cutting off early, and the clothes were not getting very warm, but better than before. Decided to change the thermal cut-off switches. Ordered the parts on Sun, they came in on Tuesday. Dryer was up and running Tuesday night. Just 2 screws per switch, took less than 1/2 hour. The dryer now runs like brand new, and my wife was ready to fork over $800 for a new one!

The dryer door latch broke

  • Customer: Theresa from Topeka, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

The Door Switch Actuator Spring had broken

  • Customer: Norman from Allen, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 7 of 9 people found this instruction helpful
I took the dryer apart by visually looking at it and removing screws, etc. until I had the top off and the front off. I took the dryer apart so I could get the part out and use it visually ascertain I was ordering the same part.

I bought the replacement part and only then did I have the instructions to take the dryer apart. It was further apart than the instructions said. I had to take the front off to retrieve the broken part which had fallen inside the front of the dryer.

I put the front back on the dryer and installed the new part, which, fortunately could only be installed one way. Once I had the two screws tightened into the part, the remainder was to simply follow the instructions that came from your web site and put the link filter and top of the dryer back on. Of course, I plugged in the dryer and checked to see that it ran before completing this.

I am amazed that I was able to find this part for a 30 year old dryer. The part hasn't changed at all. I guess, if you have a good part, there's no need to modify it.

Dryer Would Not Heat

  • Customer: John from Raleigh, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 6 people found this instruction helpful
The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.

dryer had no heat

  • Customer: gary from newcomerstown, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary

Dryer not Heating

  • Customer: Brigitte from Westerville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 7 people found this instruction helpful
Was not sure what was wrong but the Part Select site allowed us to view other repair issues and solutions. We ordered the kit, it arrived the next day (how is that possible) and easily put the parts in and chaching...money saved and dryer works better than ever. THANKS PartSelect, we give you an eleven and we will recommend you to everyone.
All Instructions for the 11060094991
61-75 of 412