Models > 11060022010 > Instructions

11060022010 Kenmore Dryer - Instructions

All installation instructions for 11060022010 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060022010
1,171-1,185 of 1,265
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Blower Wheel

  • Customer: James from Mosca, CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

I had to spin drum for dryer to start, bad start winding on motor, not sure if the problem could have been fixed by replacing the motor contactor. I could not find a part # for just the contactor.

  • Customer: Dale from Joanna, SC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

i had difficult time getting wheel off.

  • Customer: dwight from monticello, AR
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
found out that pushing in on wheel and turning counter clock wise, wheel screws off rather easy.

broken wheel

  • Customer: Ray from Coleman, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I had purchased a motor for the dryer first. The blower wheel broke while I was trying to take the motor off from the blower wheel. Installing the new wheel was fairly easy once I took the blower cover of at the back of the dryer and literally brake the wheel of the motor shaft.

Dryer wouldn't start... Just a hum when you press the start button.

  • Customer: James from Festus, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Well it took me longer to get the dryer apart and than it did to get it back together... Well I opened it up it was obvious I had burned up the motor you couldn't even see it for all the lint that was built up around it... And the hardest part was removing the fan from the motor shaft, I didn't realize it was plastic and sort of mangled it getting it off so I went ahead and replaced it as well. The hardest part of the whole repair was removing and replacing the clips that hold the motor in place and there didn't seem to be any trick to it, I used a pair of channel locks and a little muscle to get them off and back on everything else was a breeze! I recommend checking the exhaust pipe at least once a year to make sure air is flowing freely to prevent the lint build up inside and even more often if you have a long run. This should prevent having this problem again...

blower wheel cracked and broke

  • Customer: Kellie from Norton, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

Dryer would not run

  • Customer: Joe from Harrisburg, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

on-off switch

  • Customer: vincent from lesterville, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took off the back part with nut driver removed switch assembly by pressing down with a little pressure and it snapped out the new was a little different but worked on installing this was an easy assembly. just do things in reverse when finished just plug in electric and push switch to turn on. very easy to install.

Washer overflowed

  • Customer: Beth from Valley Springs, CA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

ice tray was broken

  • Customer: mike from fitchburg, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

The leveling foot on my dryer broke.

  • Customer: Diana from Clifton, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Dryer would not start

  • Customer: Marianne from Solon, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer is a KitchenAid KEYE660W (electric). I tried to start the dryer but it would not run. I did notice that if I held the start button down, I could feel light vibrations through the button. Searched through Yahoo and this site and determined that this is often a bad Thermal Fuse. Used the diagrams on this site to locate where it should be, removed the back of the dryer with a screwdriver, removed the two wires clipped to the Thermal Fuse and unscrewed the Thermal Fuse. I had a friend test the fuse with a Multimeter. It was bad so I ordered another one on this site and it arrived in two days. Screwed the Thermal Fuse back in and clipped the two wires back on. Started the dryer and it worked!!! Replaced the back of the dryer. This repair took 15 minutes MAX and taught me a little bit about Mulitmeters.

Timer went out/had bought new gas dryer/gave elect to single mom who needed it. cont..

  • Customer: TONY from JACKSONVILLE, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
dryer like new/elect, we needed, and bought a new gas dryer. Promised electric to employees daughter/ single mom with a child. Received new gas D. Electric went out the night before the daughter could pick up. Per my word, I had repair est by very trustworthy repairman, we have used for yrs.Estimate was $285 to repair. I signed into Part Select, put in model number, EVERY PART I COULD EVER NEED WAS THERE WITH PRICE. Awesome, I had given my word to daughter, so I ordered Timer, not using repairman. Ordered for $117 on Thursday, received it Monday. Took the 6 back panel screws out, two screws on bad Timer with nut drill. connected all wires as they were on old, screwed in 2 on timer, replaced screws on back panel. Finished in 5 minutes and saved $165, single mom/daughter now has awesome 4 year old dryer. She was thrilled and appreciative. Tony

Dryer made kind of a grinding noise when it started. A repair technician looked at it and said it needed new drum support rollers and shafts.

  • Customer: Janis from Lakewood, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions on the Part Select website for drum support rollers and shaft. The videos were great! (There wasn't one for the right side shaft but I could extrapolate from the other instructions.) The hardest part for me was releasing the dryer top - the video made it look so easy but it took me a long time to get the little clips to release with the putty knife. Also, tightening the new right side shaft required the help of another person as my arms are not long enough to hold the shaft with pliers while I tightened the nut in the back of the dryer (and I did have to remove the back cover for this shaft). I would recommend to anyone even a little bit handy to attempt a repair following part select's videos.

Noise due to rollers and shafts worn

  • Customer: Frank from Leechburg, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed front and back covers on dryer, screws on top and down one side to spread cabinet to remove drum,removed blower cover to get access to shaft nut on that side. The other is accessible. I found that both shafts can bethe longer of the two that were sent. The shorter shaft is too short and needed to be modified to let the roller come outward to lay in the grove in the drum. I will get a longer shaft and replace it.
All Instructions for the 11060022010
1,171-1,185 of 1,265