11060022010 Kenmore Dryer - Instructions

pop the top of the dryer open with a screwdriver(front), leatherman works well, unscrew the old switch,disconnect the wires - new part has 3 wires old one has 2 but the connector fits fine. closed up the dryer. turned it on. it works fine. A long phillips head is suggested (8") to clear the door frame so you don't beat up your knuckles.

Ordered your fuse & thermostat. Total $37.29, installed parts & still no heat. Ordered your 240v Heating element.. Total $77.43, installed part & still no heat, Removed 30amp circuit breaker and purchased replacement for $11.30 in town. Installed breaker, dryer now has heat. Still smiling as I keep telling my self I performed preventive maintenance on my dryer!!!

I followed the video directions exactly as instructed and I had no problem doing the repair myself. And if I can do it being a woman with no help you can do it. Easy peasy~

1.Installed thermal fuse. I thought this was the problem as a few years ago this fixed the dryer that was now experiencing a similar problem. Problem persisted. 2. Installed new thermostat. Problem persisted. 3. Installed new igniter coils. Eureka! Problem solved!

I simply pulled the dryer away from wall. Cleaned vents. Pulled plug out from outlet. Unscrewed the back panel and removed the cycling thermostat and fuse as per your instructions. Since I had the back panel removed I cleaned the inside of lint as well. Put the back panel back started the dryer and everything was perfect. Saved myself at least 150.00.

I ordered the part I suspected....which was indicated by approximately 44% of the users having success replacing the thermal fuse. After watching the video on how to perform the repair, it was a snap! Removed the 9 screws, removed the vent hose, popped out the fuse, and replaced it. After checking to see if that was the problem....which it was, I reassembled the dryer. It only took more time because I chose to vacuum any exposed areas. THANK YOU!

Opened top, removed front panel, snapped in new ring bearing, reinstalled front panel and top.

Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

unplug take off vent hose and back panel unscrew one bolt holding the fuse disconnect 2 wires. Connect the 2 wires to the new fuse hold in place with the bolt put back on the back panel and vent hose plug in and your done

Used PartSelect instructions for routing belt & a customer's valuable guidance.

Your website described the probability of the problem as being one or both of the replacement parts I bought. You were right. I replaced the two parts and the dryer started and has been operating flawlessly ever since. I would also like to commend you on your very rapid shipping of the parts. I recieved them in less than 24 hours, via Fed-Ex Ground.

I changed the thermal fuse following instructions from the video on the site . Very easy repair, anyone can do it.

I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.

Threw away the printed instructions and followed the Part Select video ,featuring Steve...