Models
>
1105806900
1105806900 Kenmore Iron - Overview
Sections of the 1105806900
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Light Bulb - 10W
PartSelect #: PS11739347
Manufacturer #: WP22002263
This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.
$16.32
In Stock
Water Inlet Valve - 120V
PartSelect #: PS343694
Manufacturer #: 3374621
This water inlet valve is intended for use with horizontal motor dishwashers. It uses a 3/8 of an inch valve tubing and a mounting bracket.
No Longer Available
Surface Element - 6 Inch 1200W
PartSelect #: PS11740904
Manufacturer #: WP3191455
Sold individually.
$74.88
In Stock
Hose, Inlet 6 Ft. Hose With El
PartSelect #: PS11744637
Manufacturer #: WP76314
Requires two washers.
$40.16
In Stock
TERMINAL, RING, 3/16 INCH DIA. HOLE
PartSelect #: PS333618
Manufacturer #: 247283
No Longer Available
Questions And Answers for 1105806900
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 1105806900
[Viewing 3 of 3]Will not fill with water
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher running with no or little water.
Removed screws under counter holding washer in place. Pulled washer out until I could access the back. Turned water supply off (in my case faucet under the sink) Turned power off at breaker.
Disconnected water line and electrical wires noting wire location. Removed solenoid unit by undoing two screws on frame. Installed new unit, co ... Read more nnected wires and water. Turned water on to ensure no leaks and pushed washer back under counter. Turned power back on and checked machine operation. Replaced the screws under the counter to keep machine in place. This is very easy. In my area a plumber would charge $75 to do this.
Disconnected water line and electrical wires noting wire location. Removed solenoid unit by undoing two screws on frame. Installed new unit, co ... Read more nnected wires and water. Turned water on to ensure no leaks and pushed washer back under counter. Turned power back on and checked machine operation. Replaced the screws under the counter to keep machine in place. This is very easy. In my area a plumber would charge $75 to do this.
Read less
Parts Used:
-
David from Atlanta, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
21 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my wife said no water coming to dishwasher!
i took off the kick plate and found the water valve. its the piece that water comes to from under the sink to connect to the dishwaser. it has a plug with 2 wires. i turned off the water supply, disconnected the wires(probably should have flipped the breaker but didnt) took out the 5/16 mounting screws, had to use a little end wrench on 1
... Read more
because it was behind the water line and a nut driver on the other. i put some thread gook on the connection and put the new one in the way it was and it works great. i am writing this because thats where i got the info to diagnose in the first place and saved me $$$!
Read less
Parts Used:
-
Richard from North Las Vegas, NV
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench set
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned out burner
-
Natalia from Downers Grove, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!