Models > 11047512601 > Instructions

11047512601 Kenmore Washer - Instructions

All installation instructions for 11047512601 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11047512601
16-30 of 85
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

draining problem

  • Customer: Dr. Merdad from Los Angeles CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 7 of 10 people found this instruction helpful
Open the bottom screws (hex-screw driver. remove riongs with pliers. use pan to remove excess water remained in pipes. pull to the right and remove. easier than it seems,

water would not pump (drain) out of machine

  • Customer: Pamela from Greenville OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 7 of 10 people found this instruction helpful
My husband removed the bottom panel of the washer and removed the old pump with two screws, then removed the water hose coming into the pump and unplugged the electrical push in type plug from the side of the pump. Simple reversed the process to instal the new one and replaced the front panel. Simple really...far more so than calling a repair man.

the strike hook was broken

  • Customer: david from st petersburg FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 21 people found this instruction helpful
replacing the hook was simple 2 torx screws. the latch assembly seemed ok I could hear it trying to latch the hook so i just replace the broken hook.

Door seal had gone bad leaked

  • Customer: Roy from Summerville SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 13 people found this instruction helpful
Looked how the old one came off and revearsed the process. Ordered the part, it was shipped right away and recieved it in three working days. Normal shipping too. Very pleased with the handling of my order.

Leak in the pump housing from cracked plastic

  • Customer: Mary from Rehoboth MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 4 of 6 people found this instruction helpful
Removed the old pump and installed the new one. Most difficulty came from the fact that the dryer is on top of the washer and the washer is inside a plastic pan that has a 2 inch lip which made it difficult to remover the front panel.

pump was not pumping

  • Customer: max from dewitt IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 5 of 10 people found this instruction helpful
unhooked two water lines & electrical plugin unbolted old pump and installed new pump. took about 15 minutes.

The rubber boot assembly is not the same configuration as the original equipment.

  • Customer: Mike from wilton manors FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.

replaced leaking bellows

  • Customer: thomas from santa cruz CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
I followed the description on this site, my machine was slightly different, but the basic procedure was the same. The tip to apply a small amount of the liquid soap to the bellows was useful to ease installation. Make sure the holes in the bottom of the bellows align with the drain in the bottom of the washer. The portion of the bellows that attaches to the main body via the adjustable clamp can be done by a single person with two hands. The portion that attaches to the front panel with the spring-wire band is a four hand job. Position the bellows, attach / position the wire-band with the spring portion on the bottom. Starting at the top get your helper to hold it in position, using needle nose pliers stretch the last bit of the wire-band into final position.

water would not drain

  • Customer: William from Wauseon OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 10 people found this instruction helpful
removed bottom panel and took out pump and replaced it with new one

My washer wouldn't drain

  • Customer: Melanie from McKenzie TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 4 of 7 people found this instruction helpful
My husband and son removed the old pump and replaced it with the new pump assembly. The whole process took about 30 minutes max.

stripped the threads on the water inlet

  • Customer: William from Belen NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 5 of 10 people found this instruction helpful
Be careful threading the hose to the water inlet or you
can end up cross threading or stripping the threads, they are plastic and can easily be stripped.
It will save you time and $.
Unscrew the top of the washer and remove it. Removed a weirdo screw with a pair of pliers since I didn't have the tool to remove it.
Took out the old one and replaced it with the new one. Replaced the weirdo screw with a drywall screw and screwed it in place. Carefully threaded the hoses on and turned on the water. Success!

Would not drain

  • Customer: Tammy from Maryville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 11 people found this instruction helpful
Removed bottom panel, removed hoses and pump. Reinstalled in reverse order.

Washer would not drain

  • Customer: Bruce from Massena NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 3 of 5 people found this instruction helpful
Unhooked two hose clamps took two screws off put new aprt on hooked back up works great

water running in all the time

  • Customer: Brian from Liberty NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 7 people found this instruction helpful
Turned water supply off ,took the top of washing machine off, took water valve out installed new 1unit worked ok

Locking the drum for moving

  • Customer: francis from Columbia TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
Remove the plastic caps from the rear of the machine. Insert the locking bolts into the slots. There is a clip on the bolts with a corresponding hole in the outside edge of the slots, this tells you exactly where to place the bolt. In my case i used a large flat head screw driver to move the drum into alignment with the bolt by inserting the driver into a different slot and prying the drum into place. When i had the first bolt started and about hald way in, i did the diagonly opposite bolt, got that one about half way in then did th elast two. i did not need to pry much on these two as the drum was no lined up fairly well with the bolts. I tightened them up and moved the washer. You do NOT need to call a maytag agent to come out and do this.
All Instructions for the 11047512601
16-30 of 85