Models > 11045872400 > Instructions

11045872400 Kenmore Washer - Instructions

All installation instructions for 11045872400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11045872400
31-45 of 182
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door lock was broken

  • Customer: Johnny from Homestead FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 25 people found this instruction helpful
door hook strike was broken half broke in the door the other half stayed in the lock i removed the one pcs from washer with pliers and on the door with a star wrench

Baffle broke off during wash load

  • Customer: Janice from Camden NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
It took a few minutes to realize that the part slide into place instead of snapping in. In order to get the part to slide into place i put my head in the washer to hold the drum in place then with both hands slide the part into place.

Door would not lock

  • Customer: Tina from petersburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.

Two problems- Error code FH, Water filling drum when washer off

  • Customer: William from Longwood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
The Part Select website has some great information provided by customers. I search my error code problem that shut down the washer when filling and found the most likely scenario was a faulty flowmeter.
The other problem happening at the same time was the drum filling with water when the appliance was not in use. I thought the two problems were related, but upon further research decided that the most likely cause was a faulty water inlet valve.
I order the parts from Part Select and I could not believe how fast the shipping was. I just ordered regular ground but the parts got here in a couple of days.
The repair was easy. Remove four screws (need a star bit) from the top lid of the washer and remove the cover. The flowmeter and the water inlet valve sit right on top of the washer. Even with the lousy set of pliers I used, removing the clamps and disconnecting the hoses on both parts was easy off and easy back on. I had more trouble with the electrical leads on the water inlet, only because they were on so securely and I didn't want to rip out the wiring.
All together the repair for both parts took about 30 minutes.
Make sure you turn off the water supply and be ready to mop up a little excess water from the water supply lines when you disconnect them from the washer's water inlet valve.

Kenmore Bellow between door and washer tub ripped

  • Customer: Jerome from Albquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
I followed the repair blog by the poster most liked...

Motor Control Board faulted.

  • Customer: Brent from Normandy Park WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 14 people found this instruction helpful
I read the instructions once and then started. It was easy but did take an hour to do the entire job.

Broken lock needed replacement

  • Customer: Alexander from Miami FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 10 of 14 people found this instruction helpful
The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old lock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.

Baffle broke and became disconnected from drum

  • Customer: Gregory from Geneva IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
slid new baffle into place. No directions with new part, fortunately it was easy to figure out how baffle locked into place.

Washer filling up with water when not in use

  • Customer: Dominick from Parker CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 8 people found this instruction helpful
Very simple repair:
- Turn off water and detach water supply hoses. (Good to have a bucket nearby to catch water left in hoses.)
- Remove 3 screws from the back of the lid; slide lid back 1" and lift off.
- Valve is mounted just under the lid on the back wall of the washer -- remove 1 screw from back of washer that holds valve assembly in place.
- Remove the 4 electrical connectors (2 black & 2 white) I numbered them with a sharpie so I wouldn't forget how to reattach them. :-)
- Use pliers to squeeze & slide the little hose clamp that holds the internal hose on the valve assembly. Once the clamp is out of the way, pull the hose off the valve assembly.
- Reverse the process to install the new valve assembly.

I ran into a little problem mounting the new valve assembly. The screw hole in the back of the washer did not line up with the mounting hole in the valve assembly. I had to drill a 3/16" hole just to the right of the original screw hole on the back of the washer. Used the new hole to mount the valve assembly, done.

Detergent leaking under Dispenser Drawer down front of Washer

  • Customer: Geof from Garner NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 18 of 39 people found this instruction helpful
Secondary problem was bleach being siphoned from dispenser prematurely when drawer slid in. Replaced Drawer, Detergent Container and Bleach Siphon parts. Appears to have been a change in the siphon design when compared to the original factory part. 5 loads completed since replacement of these parts with no premature siphon of bleach or leakage down the front of the washer.

Worn out hose had a hole it it.

  • Customer: Edward from Clinton MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 10 of 15 people found this instruction helpful
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

FH code-4 minutes into cycle

  • Customer: robert from LITLE RIVER SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 8 of 9 people found this instruction helpful
remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.

Washer would not spin ( F-02 comes on)

  • Customer: Steve from Dubuque IA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
1-Unplug washer
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remove 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.

kept getting sud or f2 codes

  • Customer: carroll from Paxton MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
I had sears at my house twice to fix this problem.they told me it was a penny in the pump then when that didn't work they came back and said i was using to much soap which i wasn't.What they fail to tell you is that the high effiiciency washers use less water so they put a less powerful drain pump in so they get over worked and lose the ability to get the water out so buy a new pump and it will be like it's new again.

Door leaked water

  • Customer: Tom from Spirit Lake IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 14 people found this instruction helpful
First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I removed the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps
All Instructions for the 11045872400
31-45 of 182