Models > 11044936200 > Instructions

11044936200 Kenmore Dishwasher - Instructions

All installation instructions for 11044936200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11044936200
16-30 of 156
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Movers wouldn't accept washer w/o shipping bolts

  • Customer: Rob from Yakyma WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 15 of 17 people found this instruction helpful
Like most folks, my daughter has tossed the shipping bolts after her puechase, I moved her the first time w/o any thought to it but commercial movers won't do that, they will chg. you to have it done and it's not cheap, akin to an appliance repair. This kit contains all four bolts/spacers, (2) upper and (2) lower. Hard to tell from the decription but a sweet gal on the help desk assured me of it. Got it fast and got them installed in minutes, easy to do and wrote a big note on the back of the washer to save them!! No idea why your owners book says "do not reuse".

Noisey when drum turned

  • Customer: James from North Pole AK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 14 of 19 people found this instruction helpful
To verify it was the motor making the noise not the drum bearing I removed the belt and rotated both by hand to see which one made naoise - then I ordered the motor.
To install the motor remove rear panel, slip belt off, remove 1 bolt holding motor in, carefully slide motor towards you until pivits disengage. Wires are ling enough to set motor on bottom of washer and rotate for easier access to connector. Install motor in reverse sequence.

error F 11. Mashine would not run

  • Customer: Christina from Englewood FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 22 people found this instruction helpful
removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.

Standing water in drum while not in operation. Bad solenoid on water inlet not staying closed.

  • Customer: Jay from Asheboro NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 13 people found this instruction helpful
Turn off both hot an cold water supply valves. Unscrew both hot and cold supply hoses from rear of washer making note of which inlet they came off of. Pull washer out to access screws to remove top cover and water inlet valve. Remove top cover unscrewing 3 torx screws on the rear of the washer. Unplug the 4 wires wires from water inlet valve - make sure you remember which pairs go to which solenoid. Remove 1 phillips head screw that secures the water inlet valve to the back of the washer. Remove water inlet valve. With a pair of pliers loosen the hose clamp and remove the hose from the inlet valve. Take the new water inlet valve and loosen hose clamp with pliers and push the hose onto the barbed fitting as far as it will go. Make sure hose clamp is over barbed fitting securing the hose. Attach both pairs of wires to the solenoids in the same position that you removed them. Position water inlet valve into place and secure with phillips screw. The part that I received did not quite line up with the hole on the rear of my washer so I had to elongate the existing hole on the rear of the washer with a drill so I could secure the water inlet valve as designed. Screw on both water supply lines making sure the hot and cold are screwed back on to the right inlets. Turn both water supply valves on and test looking for leaks. Secure the top cover back on with the 3 torx screws and push washer back into place. Viola! Ready for the next load of wash.

Bellow was ripped at the fold, leaking water into the casing.

  • Customer: david from Goose Creek SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
Removed the top panel. Removed the control panel (one screw behind the detergent drawer). Removed the three screws that held the door latch and switch (pushed it through). Removed the spring-loaded wire that fastens the boot to the door panel(look very closely around the bellow around the opening for the door). Removed the four screws at each corner of the front panel and removed the panel (door still intact). Loosened the band clamp that holds the bellow to the tub. Removed the vent tube from the old bellow and installed on the new bellow. Installation is the reverse of the removal. One tip: when installing the spring-loaded wire around the door panel opening, use several small (padded end) spring clamps to hold the wire in place as you install the wire. If you do not, the areas that you have installed will come undone. Be sure to be careful and use padded ends so that you lessen the likelihood of puching a hole in the new bellow.

not pumping out the water

  • Customer: Dale from Ridgely MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 14 of 22 people found this instruction helpful
Disconnected 2 hoses and 1 screw and remove3d the old pump and reversed the proceedure to install the new pump.A piece of cake. Thanks

Rubber Gasket (bellow) door seal "worn" out

  • Customer: Dan from Hudson WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 25 people found this instruction helpful
Have to remove the front two sections of the washer and top- I had to remove the control panel too. POS kenmore gasket failed after about 2.5-3 years. Old gasket got holes in it - If you have a HE3 or HE4 model- look for it! you will get them too!!! Guaranteed.

would not spin of agitate

  • Customer: Doug from Hartselle AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 12 of 16 people found this instruction helpful
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.

belt came off

  • Customer: wendy from Naples FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 14 of 22 people found this instruction helpful
Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Broken lock needed replacement

  • Customer: Alexander from Miami FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 10 of 13 people found this instruction helpful
The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old lock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.

shaking washer

  • Customer: Dean from Morrisville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 15 of 28 people found this instruction helpful
twisted old shock absorbers out and snapped new one inplace...did not really fix my problem though

Door would not lock

  • Customer: Tina from petersburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.

Washer filling up with water when not in use

  • Customer: Dominick from Parker CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 8 people found this instruction helpful
Very simple repair:
- Turn off water and detach water supply hoses. (Good to have a bucket nearby to catch water left in hoses.)
- Remove 3 screws from the back of the lid; slide lid back 1" and lift off.
- Valve is mounted just under the lid on the back wall of the washer -- remove 1 screw from back of washer that holds valve assembly in place.
- Remove the 4 electrical connectors (2 black & 2 white) I numbered them with a sharpie so I wouldn't forget how to reattach them. :-)
- Use pliers to squeeze & slide the little hose clamp that holds the internal hose on the valve assembly. Once the clamp is out of the way, pull the hose off the valve assembly.
- Reverse the process to install the new valve assembly.

I ran into a little problem mounting the new valve assembly. The screw hole in the back of the washer did not line up with the mounting hole in the valve assembly. I had to drill a 3/16" hole just to the right of the original screw hole on the back of the washer. Used the new hole to mount the valve assembly, done.

Worn out hose had a hole it it.

  • Customer: Edward from Clinton MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 10 of 15 people found this instruction helpful
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.
All Instructions for the 11044936200
16-30 of 156