Models > 11044936200

11044936200 Kenmore Washer - Overview

Get Parts and Repair Help for 11044936200

If you know the washer repair part you need, you can browse the list of all parts on the 11044936200, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11044936200 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.


Door Lock Latch

This part is used on front load washers and includes the interlock switch assembly.


Water Inlet Valve

Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.


Shock Absorber

Shock absorbers help keep the washer from vigorous shaking during its cycles. Sold individually.



This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.


Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.


Bellow Clamp

This is used to help hold the bellow in place.


Touch-Up Paint - White



Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear. NOTE: Per Manufacture, belt measures 48...


Door Hook/Strike

Attaches to door lock mechanism.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 143 of 148 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more

front load washer latch replacement

  • Customer: James from Vilonia AR
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 113 of 129 people found this instruction helpful
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. r... read more

Washer made loud banging noise during spin cycle

  • Customer: Francis from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 71 of 85 people found this instruction helpful
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in s... read more