Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11044832200

11044832200 Kenmore Washer - Overview

Get Parts and Repair Help for 11044832200

If you know the washer repair part you need, you can browse the list of all parts on the 11044832200, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11044832200 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$157.24

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$78.98

Door Lock Latch

This part is used on front load washers and includes the interlock switch assembly.

$58.26

Water Inlet Valve

Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

$40.29

Shock Absorber

Shock absorbers help keep the washer from vigorous shaking during its cycles. Sold individually.

$41.76

Flowmeter

This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.

$19.50

Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.

$3.02

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$22.61

Pump Hose

This hose attaches to water pump assembly. NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.

$6.92

Door Hook/Strike

Attaches to door lock mechanism.

$30.36

Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear. NOTE: Per Manufacture, belt measures 48.22" long uninstalled and the belt will stretch To 51.53" when installed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 198 of 204 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more

front load washer latch replacement

  • Customer: James from Vilonia, AR
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 160 of 182 people found this instruction helpful
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. r... read more

Tub of front load washer was slowly filling with water when machine was empty/off

  • Customer: Andrea from Chelmsford, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 110 of 116 people found this instruction helpful
Pulled out machine...removed top panel..unscrewed existing valve and removed it...then reversed the whole process with the new valve..it was very easy to do and worked perfectly...no more water in tub! read more