Models
>
1104319410
1104319410 Kenmore Dryer - Overview
Sections of the 1104319410
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
M Series New Style Coil Kit
PartSelect #: PS334310
Manufacturer #: 279834
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
$30.89
In Stock
Igniter Kit
PartSelect #: PS334180
Manufacturer #: 279311
If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-in...
$40.54
In Stock
Screw
PartSelect #: PS11743744
Manufacturer #: WP681414
This screw is sold individually.
$7.76
In Stock
Natural Gas Orifice for Dryer Gas Valve
PartSelect #: PS11740485
Manufacturer #: WP234826
$26.46
In Stock
Natural Gas Limiter
PartSelect #: PS11743791
Manufacturer #: WP694424
The leak limiter or natural gas limiter is used in dryers. This part acts as a cover of the adjustment screw on the pressure regulator. If you are changing from propane (LP) back to natural gas, it is...
$31.58
In Stock
Gas Valve Kit
PartSelect #: PS334359
Manufacturer #: 279923
This gas valve kit comes with the wiring harness.
$403.92
In Stock
Questions And Answers for 1104319410
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 1104319410
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer ran but would not heat
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are
... Read more
located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
Read less
Parts Used:
-
Gary from Haverhill, NH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
390 of 439 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils
... Read more
& the problem was corrected.
Read less
Parts Used:
-
andy from Bethesda, MD
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
202 of 224 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer wasn't working (New Timer)
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or
... Read more
dered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.
Read less
Parts Used:
-
Joaquin from Las Vegas, NV
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
158 of 198 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!