Models > 11042926200 > Instructions

11042926200 Kenmore Washer - Instructions

All installation instructions for 11042926200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11042926200
151-156 of 156
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

pump wouldnt drain

  • Customer: Edward from Dayton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
removed three screens on lower front panel removed hoses from pump after opening drain/filter to remove water slid pump forward and out unplugged pump wiring harness reverse to install

Kept getting F2 code and washer wouldn't drain

  • Customer: Janet from Sutton WV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the front panel below tub and above pedestal off washer. Removed pump and found coins in the strainer. Removed them thinking they may be causing the problem. Put everything back together and tried again. Washer still wouldn't drain. Unplugged it and ordered a new pump. Installed pump after removing the plug and draining water from washer. Replaced pump with new one and washer works like new.

Easiest $300 I've ever saved!!!

  • Customer: Rusty from Pascagoula MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Part was $150 and the going rate to replace the pump by a repair person is $300=$450. This was super easy and took about 15 minutes, including draining the old pump with my wet vac!! I messed around witht he old one trying to clean it, etc for several weeks because I'm cheap and didn't want to spend the $150. SPEND THE MONEY AND DO IT YOURSELF.

Water collecting in tub next day after use

  • Customer: Jerome from Ashburn VA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
(1) Turn off water valves (2) remove water lines (3) remove three metric star screws from top/back of washer (4) remove to plate (5) remove single screw retaining water inlet valve at back of washer (6) remove electrical connections from water inlet valve and flow meter (7) loosen hose clamps at back of soap dispenser (8) remove assembly/apply new parts (9) reverse above directions. Because the plastic nipple at the back of the soap dispenser was brittle, it partially broke on me. I applied urethane glue to the break and let it dry overnight. Next day I applied marine-grade silicone sealant around the break area. That evening I assembled and then used the washer to test for leaks. Success!

F/H error

  • Customer: Harry from Lodi CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooked the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.

F/H error code

  • Customer: Harry from Lodi CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I replaced the flow meter but that want it, so replaced the water inlet valve and that cured what ailed it. The only pain was that the single screw that holds the part to the washer is a torx rather than a nut like the rest of the back screws. Couldn't see it without pulling the washer all the way out. Hose clamp came off with pliers and the electrical connectors were TIGHT but came off with some effort. Replaced everything and error cleared ok.
All Instructions for the 11042926200
151-156 of 156