Models > 11042922200 > Instructions

11042922200 Kenmore Dishwasher - Instructions

All installation instructions for 11042922200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11042922200
46-60 of 156
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replace motor

  • Customer: David from Eleva WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
Everything went great from order to done. Very happy

Door would not open.

  • Customer: MIKE from LONGWOOD FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
It takes 2 people to do this repair.The bellow is the hardest part. One person has to hold the bellow in one spot, and the other person has to put it on the rim of the drum all the way around. Sort of like putting a tire on a bicycle. Dont do what I did and pry the door open. If you do that you will have to get a new door lock control at $54.Take off the lower front panel and reach up to the manual releace tab on the right side and pull down. Please make sure that the power is turned off, unplug the washer from the wall for your safety. The door switch itself is easy to replace, 3 screws, 3 plugs. Hope this helps.

leak suddenly developed

  • Customer: Gerald from Troy NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
Somehow a bobby pin got into the drain pump housing. When it started to drain, the pin was rammed through the housing.Extremely easy to remove and replace. No special skills needed. Whirlpool did a good job in making it idiot proof. Unpacking the part took longer than installing it. Don't be afraid to do this repair. If you own a pair of pliers and a screwdriver,you can do it.

washer not drain or spin

  • Customer: LAURA from SPARTA KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.

Washer would not operate, water in drum would not drain. Error code indicated a bad pump

  • Customer: Patrick from Beaumont TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately $150.00 bucks in repair service fees.

Low water intake pressure error

  • Customer: John from Rye Brook NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 4 of 4 people found this instruction helpful
Serviceman had previously replaced the hot and cold inlet valves, but the low pressure error persisted. Rather than cough up another $130 for the serviceman to return, plus parts and time, I decided to order the replacement flowmeter from PartSelect.

Unplug power and turn off water. Top of machine comes off by removing three screws at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.

Great move, easy, and saved myself the thick end of $200.

The water didn't drain, so the drum wouldn't spin

  • Customer: Jill from New Rochelle NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

Tub would not drain even though pump was running

  • Customer: Steve from Cary NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.

FOLLOWING THE INSTRUCTIONS OF THE REPAIR MANUEL,

  • Customer: gerard from arvada CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
FIRST I REMOVED THE RETAINER RING AND THEN PULLED BACK ENOUGH OF THE BOOT TO GET THE DOOR SWITCH OUT AND PLUGGED IN THE NEW SWITCH PUT THE RETAINER RING BACK ON AND IT WAS FINISHED. WITH OUT THE REPAIR BOOK I WOULD HAVE BEEN LOST ON HOW TO DO THE JOB.

washer filled with water overnight

  • Customer: ROBERT from Millville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
following the procedure was easy except the alignment of the new valve was off by 1/4 inch and I had to drill an additional hole to reuse the screw for attachment. Piece of cake otherwise.

The washer was unable to run without door locking

  • Customer: MICHAEL from DERIDDER LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .

Pump not working

  • Customer: Darrell from Lady Lake FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Replaced pump

Shaft in water pump broke

  • Customer: Jeffrey from Adrian MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 3 of 3 people found this instruction helpful
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

Broken baffle

  • Customer: michael from barrington RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 10 people found this instruction helpful
I wasted 2 years washing clothes in mu Duet before I repaired it in just two minutes. In those 2 years we destroyed numerous articles of clothing because the missing baffle left sharp metal corners that cut holes in to so many of our clothes. The replacement baffle was easy to find on partselect.com as were installation guides. I can't believe how easy it was!

Pump not draining the water out.

  • Customer: Martin from Kotzebue AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
All Instructions for the 11042922200
46-60 of 156