Models > 11042922200 > Instructions

11042922200 Kenmore Dishwasher - Instructions

All installation instructions for 11042922200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11042922200
16-30 of 158
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

error F 11. Mashine would not run

  • Customer: Christina from Englewood FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 18 of 25 people found this instruction helpful
removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.

Water would not drain, motor died

  • Customer: Michael from Worcester MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 16 of 20 people found this instruction helpful
Remove the lower front cover there are three small torx type screw. The pump is the very first thing you see. Have a wet and dry Vac available you will need it. The drain pump and the drain lines contain a lot of water. Unscrew the big white drain plug at the pump and clean up the water, remove the front small mounting screw and disconnect the two hoses in the back of the pump with pliers and follow the pre-printed steps in reverse. If your machine is more than six years old you will have to use a utility knife and remove a piece of plastic on the electrical connector that is from the washer wiring, if you force the connection on it will brake, look at the connection and the plug and attempt to plug it in before you install the pump. It is easy just be-aware of the connector.

Noisey when drum turned

  • Customer: James from North Pole AK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 15 of 20 people found this instruction helpful
To verify it was the motor making the noise not the drum bearing I removed the belt and rotated both by hand to see which one made naoise - then I ordered the motor.
To install the motor remove rear panel, slip belt off, remove 1 bolt holding motor in, carefully slide motor towards you until pivits disengage. Wires are ling enough to set motor on bottom of washer and rotate for easier access to connector. Install motor in reverse sequence.

Standing water in drum while not in operation. Bad solenoid on water inlet not staying closed.

  • Customer: Jay from Asheboro NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 14 people found this instruction helpful
Turn off both hot an cold water supply valves. Unscrew both hot and cold supply hoses from rear of washer making note of which inlet they came off of. Pull washer out to access screws to remove top cover and water inlet valve. Remove top cover unscrewing 3 torx screws on the rear of the washer. Unplug the 4 wires wires from water inlet valve - make sure you remember which pairs go to which solenoid. Remove 1 phillips head screw that secures the water inlet valve to the back of the washer. Remove water inlet valve. With a pair of pliers loosen the hose clamp and remove the hose from the inlet valve. Take the new water inlet valve and loosen hose clamp with pliers and push the hose onto the barbed fitting as far as it will go. Make sure hose clamp is over barbed fitting securing the hose. Attach both pairs of wires to the solenoids in the same position that you removed them. Position water inlet valve into place and secure with phillips screw. The part that I received did not quite line up with the hole on the rear of my washer so I had to elongate the existing hole on the rear of the washer with a drill so I could secure the water inlet valve as designed. Screw on both water supply lines making sure the hot and cold are screwed back on to the right inlets. Turn both water supply valves on and test looking for leaks. Secure the top cover back on with the 3 torx screws and push washer back into place. Viola! Ready for the next load of wash.

belt came off

  • Customer: wendy from Naples FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 16 of 24 people found this instruction helpful
Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.

not pumping out the water

  • Customer: Dale from Ridgely MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 15 of 23 people found this instruction helpful
Disconnected 2 hoses and 1 screw and remove3d the old pump and reversed the proceedure to install the new pump.A piece of cake. Thanks

Bellow was ripped at the fold, leaking water into the casing.

  • Customer: david from Goose Creek SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
Removed the top panel. Removed the control panel (one screw behind the detergent drawer). Removed the three screws that held the door latch and switch (pushed it through). Removed the spring-loaded wire that fastens the boot to the door panel(look very closely around the bellow around the opening for the door). Removed the four screws at each corner of the front panel and removed the panel (door still intact). Loosened the band clamp that holds the bellow to the tub. Removed the vent tube from the old bellow and installed on the new bellow. Installation is the reverse of the removal. One tip: when installing the spring-loaded wire around the door panel opening, use several small (padded end) spring clamps to hold the wire in place as you install the wire. If you do not, the areas that you have installed will come undone. Be sure to be careful and use padded ends so that you lessen the likelihood of puching a hole in the new bellow.

shaking washer

  • Customer: Dean from Morrisville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 18 of 32 people found this instruction helpful
twisted old shock absorbers out and snapped new one inplace...did not really fix my problem though

Two problems- Error code FH, Water filling drum when washer off

  • Customer: William from Longwood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 12 people found this instruction helpful
The Part Select website has some great information provided by customers. I search my error code problem that shut down the washer when filling and found the most likely scenario was a faulty flowmeter.
The other problem happening at the same time was the drum filling with water when the appliance was not in use. I thought the two problems were related, but upon further research decided that the most likely cause was a faulty water inlet valve.
I order the parts from Part Select and I could not believe how fast the shipping was. I just ordered regular ground but the parts got here in a couple of days.
The repair was easy. Remove four screws (need a star bit) from the top lid of the washer and remove the cover. The flowmeter and the water inlet valve sit right on top of the washer. Even with the lousy set of pliers I used, removing the clamps and disconnecting the hoses on both parts was easy off and easy back on. I had more trouble with the electrical leads on the water inlet, only because they were on so securely and I didn't want to rip out the wiring.
All together the repair for both parts took about 30 minutes.
Make sure you turn off the water supply and be ready to mop up a little excess water from the water supply lines when you disconnect them from the washer's water inlet valve.

Drum didn't turn/spin

  • Customer: john from chester NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 15 of 25 people found this instruction helpful
1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry

Rubber Gasket (bellow) door seal "worn" out

  • Customer: Dan from Hudson WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 25 people found this instruction helpful
Have to remove the front two sections of the washer and top- I had to remove the control panel too. POS kenmore gasket failed after about 2.5-3 years. Old gasket got holes in it - If you have a HE3 or HE4 model- look for it! you will get them too!!! Guaranteed.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

FH code-4 minutes into cycle

  • Customer: robert from LITLE RIVER SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 10 of 11 people found this instruction helpful
remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.

Motor Control Board faulted.

  • Customer: Brent from Normandy Park WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 15 people found this instruction helpful
I read the instructions once and then started. It was easy but did take an hour to do the entire job.

would not spin of agitate

  • Customer: Doug from Hartselle AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 12 of 18 people found this instruction helpful
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.
All Instructions for the 11042922200
16-30 of 158