Models > 11042822200

11042822200 Kenmore Washer - Overview

Get Parts and Repair Help for 11042822200

If you know the washer repair part you need, you can browse the list of all parts on the 11042822200, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11042822200 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$73.55

Door Lock Latch

This part is used on front load washers and includes the interlock switch assembly.

$139.85

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$53.75

Water Inlet Valve

Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

$33.31

Shock Absorber

Shock absorbers help keep the washer from vigorous shaking during its cycles. Note: They are sold individually. Order quantity needed.

$13.64

Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.

$4.95

Touch-Up Paint - White

$3.76

Door Hook/Strike

Attaches to door lock mechanism.

$14.54

Bellow Clamp

This is used to help hold the bellow in place.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.70

Hose Clamp

This hose clamp is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 106 of 110 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more

front load washer latch replacement

  • Customer: James from Vilonia AR
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 87 of 100 people found this instruction helpful
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. r... read more

My washer would not always finsh the cycle (most of the time it would run between 2 and 30 minutes) and then the time display would flash and the washer would shut down and beep. An f06 fault code flashed in the display.

  • Customer: Bradley from Red Wing MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 66 of 74 people found this instruction helpful
First I removed the screws and the plastic slide clips to remove the back plate. I then went to the lower right of the washer and found the motor control unit. It has about four plus going into it. The front inside mount of the control unit has a clip on it that must be pushed so you can pull the unit free of the bottom of the machine. Once the control u... read more