Models
>
110402-0206-E1
110402-0206-E1 Briggs and Stratton Engine - Overview
Sections of the 110402-0206-E1
[Viewing 9 of 9]Keep searches simple, eg. "belt" or "pump".
Filter- A/C Cartridge
PartSelect #: PS8987387
Manufacturer #: 491588S
This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this...
$7.06
In Stock
Starter Pawl-Ratchet
PartSelect #: PS8942598
Manufacturer #: 281505S
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will...
$3.99
In Stock
Kit-Needle/Seat
PartSelect #: PS8963322
Manufacturer #: 398188
This needle and seat kit, also known as a float valve, is found in many types of liquid-fueled lawn equipment, such as carburetors. The valve regulates the flow of fuel into the float bowl. The needle...
$6.91
In Stock
Starter-Rewind
PartSelect #: PS8981884
Manufacturer #: 497680
This recoil starter is for lawn and garden equipment engines.
Recoil starter spins the crankshaft to start the engine when you pull the rope.
$54.25
In Stock
Fuel Tank
PartSelect #: PS9141053
Manufacturer #: 799863
This is a replacement fuel tank for your outdoor power equipment. It is made of black plastic and comes with the tank itself, as well as the fuel cap. The fuel tank stores fuel before it is transporte...
$98.07
In Stock
Questions And Answers for 110402-0206-E1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 110402-0206-E1
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
starter rewind cord broke
I found the model number of the Briggs & Stratton engine on the inside of the engine housing. Ordered a new starter-rewind unit, as the old cord broke and the thing was well worn. The instructions were clear enough, but to get the old starter off I had to drill out four rivets, which just spin around when you try. I used a hacksaw, chisel
... Read more
, pliers, whatever worked on each rivet; this took a while. When they were finally removed, the new starter pull unit was relatively easy to install with the small nuts and bolts provided. On the Yard Machines log splitter, putting back the engine housing is quite tricky; you have to jostle the thing into place, get the pull handle above the cover and line up the bolt holes.
Read less
Parts Used:
-
Seikai from MARICOPA, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
9 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Parts Used:
-
Alberto from PALMETTO BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
7 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!