Models
>
110359055
110359055 Kenmore Washer - Overview
Sections of the 110359055
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Spin Pinion Seal
PartSelect #: PS11741857
Manufacturer #: WP356427
This seal is for the top of basket drive tube shaft.
$11.14
In Stock
SEAL-SHAFT
PartSelect #: PS11746864
Manufacturer #: WP91939
This OEM upper transmission shaft seal, also known as the oil seal, is found in your washers and dryers. It acts as a barrier to prevent water from leaking into the transmission assembly. It measures ...
$8.00
In Stock
RING-WIRE
PartSelect #: PS11773107
Manufacturer #: W11033823
This is part of the Basket Drive and found under the Brake Lining parts.
$7.43
In Stock
Wig Wag Solenoid
PartSelect #: PS396111
Manufacturer #: 84867
This transmission shifting coil set has 2 solenoids - one turns to start the agitating during the wash cycle and the other turns on to start the spin-dry cycle. Only one solenoid is operating at one time.
No Longer Available
Wig Wag Plunger Kit
PartSelect #: PS347742
Manufacturer #: 350384
This wig wag plunger kit comes with a plunger, a cam bar guide, a rivet, and a speed nut.
No Longer Available
SPRING
PartSelect #: PS334601
Manufacturer #: 285672
CONTAINS ONE EACH:
92814 SEAL
No Longer Available
Questions And Answers for 110359055
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 110359055
[Viewing 3 of 3]Leaking
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not spin on any cycle. The pump still work so it was not the belt.
The wig wag selenoid was not shifting the transmission to the spin mode. Using a 5/16 nut driver remove the two screws holding the back access panel. Using the same driver remove the set screw holding the wig wag onto the shaft. Lift the part off the shaft. If it is hard, using a small pry bar. Install new part and reverse the process
... Read more
.
Read less
Parts Used:
-
Richard from Newark, DE
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
34 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't go out of spin brake mode
Used Liquid Wrench to loosen wig-wag solenoid bracket. Drilled out rivet on defective wig-wag plunger. Installed new one with easy-to-install rivet clip. Now works like a charm.
Parts Used:
-
Mike from Roeland Park, KS
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced wigwag solenoid: washer spun and drained but did not agitate
pulled leads off old wigwag solenoid, removed set screw and sprayed shaft w/wd40 then tapped it off shaft w/small hammer and large screwdriver. put new wigwag solenoid onto shaft then tapped it down into place and tapped it to rotate to expose set screw hole. reattached set screw, reattached leads to solenoid, checked looseness/freeness o
... Read more
f cam arms and it worked
Read less
Parts Used:
-
eric from moreno valley, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!