Models > 11029072990

11029072990 Kenmore Washer - Overview

Get Parts and Repair Help for 11029072990

If you know the washer repair part you need, you can browse the list of all parts on the 11029072990, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11029072990 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$11.77

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added stren...

$29.84

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$30.40

Lid Switch Assembly with Leads

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$15.44

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. I...

$28.77

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").

$3.76

Tub Spring

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$7.38

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$2.70

Hose Clamp

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer stopped mid cycle

  • Customer: Travis from Pearland TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 587 of 591 people found this instruction helpful
1. Unplug washer.
2. Remove screws at control panel end caps.
3. Flip control panel back to expose wiring.
4. Detach lid switch wiring harness from control panel.
5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
6. Tilt the front/sides piece over to expose lid switch.
read more

The lid switch had broken on my washing machine; the machine would not run.

  • Customer: Dennis from Evans City PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 493 of 513 people found this instruction helpful
First I unplugged the washing machine. Then I removed the two screws that hold the top console in place; these are located in back of the main console (where the dials are). Once removed, the entire console swivels back, exposing the wires underneath. I unplugged the wiring harness that was connected to the washing machine top flat surface. I then remove... read more

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 496 of 529 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more