Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11026912691 > Instructions

11026912691 Kenmore Washer - Instructions

All installation instructions for 11026912691 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11026912691
1,006-1,020 of 1,280
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

motor running . no spin cycle

  • Customer: joe from loveland, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Tipped the washer on its side and took the pump off then the motor then the coupling.

Washer was not spinning, but making a loud spinning noise.

  • Customer: William from Sonoma, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Disconnected power. Disconnected hot and cold, and drain hoses and placed in a plastic bucket. Pulled cover off the washer. Tilted washer onto its back. Removed 2 clips holding the pump. Disconnected wire harness from motor and removed 2 clips holding motor starting with lower clip. Removed a screw from the upper clip used for shipping. Set motor aside and removed broken pieces of the motor coupler from motor and transmission. The replacement part had a metal sleeve in the center of each white plastic ring. The old part did not. This required tapping the new ring onto both the motor and transmission shafts with a socket and makes for a tight fit. Reversed the process to put everything back together. Some alignment might be necessary to place motor to transmission. I recomment wearing thin work gloves to avoid nicks from sharp edges. I didn't. Washer is spinning again and sounds a lot better.

Washer would not spin after washing.

  • Customer: Steve from Summerfield, NC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
We followed the step by step video that you had posted for those parts. It is now working wonderfully. The repair man had told us it could not be repaired. Thank you so much for having these do it yourself instructions.

Washer would not spin

  • Customer: Laura from Ocala, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I Googled "washer would not spin" and came upon the PartSelect YouTube video on replacing the motor coupling. Since this seemed easy enough (and I'm a 40-year-old Mom), I decided to take the washer apart as the video instructed just to see if I could find anything obviously broken or out of place. Low and behold, the rubber gasket around the coupling was broken and indicated the coupling probably was too. I ordered the part through the direct link on the YouTube video and easily put the new coupling on and VOILA! The only thing I'd recommend differently is that you leave the pump alone. It doesn't need to come off to get to the coupling. After wrestling with trying to remove the pump, I left it in place, but not before unknowingly damaging it. I had some rust build-up in there and it made the fit very tight and cracked the part/sleeve the motor drive plugs into. When the washer was reassembled I found I'd caused a leak. But...no biggie. I decided to replace pump, too. Hey, now I know how to! :) Just received that part yesterday and VOILA! It's amazing what you can accomplish with the internet. Don't be afraid of this task, ladies (and gentlemen).

washer pumped water out but would not spin

  • Customer: brian from shohola, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
took the washing machine out of the washroom closet and did the repair in the kitchen

Washer vibrating when in spin cycle.

  • Customer: Calvin from Cheney, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced suspension, leveling and tub springs.

when it would spin it would sheakall over .

  • Customer: Johnny from Las Cruces, NM
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just did it how the way it showed on the video it was easy

Washer vibrated during the spin cycle

  • Customer: David from Roswell, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

Out of balance, could't operate

  • Customer: Arlyn from Driggs, ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The prooblem started with the hole in the bottom frame, for tub spring wore through, spring fell off, then a spring retainer worn broke in 2 releasing 1 suspention spring. All springs were about to fail, metal very thin at at the contact points. Drilled a new hole for the new suspension spring, replace all 3 brackets, worn also, springs, and retainers with a small dab of grease at the contact points. The new springs mad the tub more stable than before the failure, and silent when spinning or washing. Be careful to get the springs in the right direction, then the spring comes over the outside the brackets and retainers, other way they rub in spots. On this machine one was backwards from the factory 18 years ago, surely that accounts for more stable running.

Tub was slamming side of tub during spin cycle and getting all out of balance

  • Customer: Steven Arthur from Tifton, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the cabinet apart really easily with Part Selects helpful video. Removed old suspension springs by removing outer brackets on two of them and by using pliers on the third one. The tub spring was totally missing. Put on two new brackets and springs with the nut driver. Then stretched the third spring into place. Replaced the tub spring by stretching into place and then put cabinet back together. All done very quickly!!! Now it works perfectly and runs very quietly.

Machine wobbled during spin cycle. Appeared to have some loosened part in the rear of the machine (noted some flexing on the front of the cabinet during spin).

  • Customer: Jonathan from Brandon, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.

Washer shook in the SPIN cycle.

  • Customer: Mark from Dagsboro, DE
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

Extremely wild rocking in spin cycle

  • Customer: Bryan from Midland, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

Water leaking from under front of machine

  • Customer: Kevin from Avondale, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the video and reading some of the instructions posted on Parts Select I disconnected the power cord, shut off and disconnected the water lines before laying the washer down on its "back" with help of a dolly.(IF you don’t own a dolly this can still be done without one but I recommend having a friend help you depending on your age and health) Once I had the washer laid down it became apparent to me that I didn’t need to take the whole "cover" off but could do the repair from the bottom of the machine. Following the instructions I first removed the hose clamps from the hose running from the pump to the tub and the hose that runs to the back of the machine where the drain to the wall attaches. I then "popped" the two clips off the pump as described in the video and after removing the pump I turned the clips to the side and removed them as well. At this point I removed the clamp from the "pump to tub" hose on the tub side and then removed the hose. I followed this up by removing the entire hose assembly that the "pump to drain hose" hose attaches too. Once you've seen this "assembly" you'll understand what I mean. Anyway, once that was done and the new parts had arrived (parts came quickly I placed my order on Thru evening and received them on Tues with the Labor Day weekend in-between) Install was as simply as removal, I laid the machine down using the dolly and then simply installed everything starting with "pump to drain hose assembly" then the "tub to pump hose" then the pump itself and finally both hoses to the pump. The "pump to tub" hose came with two new clamps however they are the type of hose clamps requiring the use of a screw drive to tighten not the original type it had on it that you just squeeze with pliers. I used the new ones that came in the package. The other hose didn’t come with a clamp and only has one where it connects to the pump, so I reused the original. I would suggest that you also check or just replace the drain line that runs from the machine to the wall at the same time as the rest of this repair as I did not and the 1st time I ran the machine that hose sprung a leak.

Washing machine leaking water out from bottom

  • Customer: David from Friedens, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected power cord. disconnected water lines, pulled outer drain hose out of home drain standpipe. tilted unit forward. removed outer drain hose. removed mounting screw for drain pipe with nut driver. removed inner drain hose (defective part) with pliers. installrd new part in reverse order. new part fit like a glove.
All Instructions for the 11026912691
1,006-1,020 of 1,280