Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11026912691 > Instructions

11026912691 Kenmore Washer - Instructions

All installation instructions for 11026912691 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11026912691
991-1,005 of 1,280
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Spin cycle would not complete or spin fast enough

  • Customer: Evan from Batavia, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Replaced Cltch assembly. Hardest part was figuring out how to drop the motor. The clutch is located of the main shaft above the motor, under the drum. Three bolts hold the motor in from underneath, however there is a bolt at the top of the shaft in the agitator assembly. Note location of the snap ring on the shaft holding the clutch assembly, grooves in shaft. The only other issue that I had is the is a triangular metal peice that is not attached in anyway between the drum and framing. It had moved when I had the motor and had to be reset after I did my first test run of washer. Spins out great now!

Agitator wouldn't turn

  • Customer: Simone from Danville, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the agitator and the broken directional cogs. Ordered the new ones; recieved them within a couple of days. Replaced the cogs; in no time the washer was working like new.

washer agitator wasn't working properly

  • Customer: Francis from Valley Lee, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I followed the video clip that showed how to make the repair that was attached to the email sent from Patrselect notifying me that my part had been shipped. The video clip was excellent and no other instructions needed. Thanks

top portion of agitator free spinning

  • Customer: gregory from camp hill, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed center top cap/sofetner dispenser. Removed center shaft bolt. Pulled off the top agitator section from bottom portion. Inside the upper agitator is the inner housing for the cogs, pushed right out. Remove cog retainer plastic ring. Careful, the cogs freely fall out and it a little tricky when reassembling. Reassemble every (cogs go in only one way), place the upper agitator back down and over lower portion in machine. Now Put the bolt back in place. Here's the tricky part. You will need a magnetic tip driver or socket to hold the bolt until you have it started because it sits in recessed "well" area. I used a dab of regular Elmer's glue from bolt head to socket. Worked like a charm. Be careful not to over tighten bolt. Remember, upper agitator should free spin one direction and "catch" in the apposing direction.

Spin cycle not working.

  • Customer: Thomas from Brighton, MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Almost identical to the instruction video that was sent. Very straight forward. I did not take apart the washer to identify the problem. I was short on time so I took a chance and ordered the highest probability cause of the symptoms indicated by your website. It was dead on; the problem is fixed. Parts were received ahead of schedule. Excellent all around.

Washer was not spinning clothes on 1st spin

  • Customer: Jeff from Westfield, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After researching possible failure modes and reviewing a video for teardown/access from the control panel and access top down I noticed a lot of 'break dust' on top of the transmission. Shorting out the lid switch and putting my little finger on the drum, it would not spin but the clutch was spinning fine. I ordered a new clutch... Interesting thing when I was taking the clutch out... the gear it was attached to slid right off! After figuring out it was too big to go 'back' into the transmission and reviewing the parts explosion diagram... it BELONGED INSIDE THE TRANSMISSION! So I took the transmission cover off, poured out out the black-ish oil with metal filings in it, put the gear inside, filled it back up with 10W30, put the lid on, added the new clutch while it was apart and finished reassembly. Wow! It spins much better than when it was new. I guess never assume what can happen on an assembly line. Thanks for the great site.

washer not spining

  • Customer: Israel from san antonio, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
took motor of 2 screws instaled motor coupling

Water inlet valve failed.

  • Customer: Robert from Des Peres, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The training video you supplied was right on. I watched it twice to make sure I understood the procedure. I followed the steps outlined in the video and encountered no surprises. The replacement valve was a perfect match and functioned perfectly after installation. I checked other sources for the price of the replacement part. Your price was more than competative. Thank you for a fine service.

Water Pump Leaks

  • Customer: jose from mnroe, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
It was really easy, just follow the video. The washer machine sounds like new now.

Machine fills then just hums

  • Customer: Kevin from Center Point, TX
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After alot of helpful advise from you guys I replaced coupling water pump clutch, and the problem was still their. Then I tested motor capacitor and it appears dead. So I should receive new one tomorrow and hopefully success! I turned machine over and oil leak..so that's where the string with hose and air needle come in handy to put 90weight oil in through breather hole in gear case.

Water inflow did not shut off when tub full.

  • Customer: Edwin L from Santaquin, UT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed video instructions.

no spin cycle at all still pumps

  • Customer: rex from yorba linda, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed website instructions, worked for a couple days, appears it needs clutch or possibly transmission(red oil present)

Leaking water where shaft goes into pump

  • Customer: Dale from Hugo, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Pulled off clamps, removed 2 clips, pryed off pump from shaft, sanded shaft(as it had rust on it) put a dab of oil on shaft, installed pump, hold down clips and hose clamps.

will not spin

  • Customer: Fred from Centerburg, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
one thing that you do not need to do is to remove the pump from the motor, I tried to remove it as per the instructions but the pump cracked,remove both inlet and outlet hoses from the pump and remove the pump and motor together, don't try to take them apart, you don't need to, thanks

Washing Machine stopped spinning and agitating, clicking/hum noise when lid closed.

  • Customer: DAVID from BATH, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Did not know problem or how to access - thought the back came off washer. Typed in symptoms and it pretty much pinpointed the most likely cause. Watched video on how to take it apart (BTW the front and sides come off, NOT the back). Followed the guide, took motor off and sure enough one of the plastic couplers was cracked. Ordered from PartSelect and with regular shipping the cost was under $20 (ordered Tues. night, had it by Thurs.) Installed part - note as someone else said the new piece has metal inserts which make it really snug to go around the drive shaft, but the tip about using an oversized socket and some light taps to get it on worked liked a charm. Put it all back together (getting case back on was toughest part)and its been working fine for the last week - heavy & lite loads. Have to say was thinking the whole thing needed to be replaced (sound & age) but for $20 it was worth the shot...Glad i came here first!
All Instructions for the 11026912691
991-1,005 of 1,280