Models > 11026912691 > Instructions

11026912691 Kenmore Washer - Instructions

All installation instructions for 11026912691 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11026912691
976-990 of 1,269
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

leaking water pump

  • Customer: Erin from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the outer shell of the machine, and disconnecting the supply hoses, I leaned the machine on it's back and disconnected the drain line. Then, it was simply a matter of removing and replacing the damaged pump with the new one. The pump is held in place by two easily removable clips. The hardest part of the whole process was making sure the shaft from the motor lines up with the corresponding hole on the pump.

Leaking water from under the front of the washer

  • Customer: John from Morgantown WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Used pliers to help disconnect hoses, unplugged power cord, laid washer on its back, unsnapped two clips holding pump to the motor, lifted pump off, and replaced it.

Water wouldn't drain after wash cycle.

  • Customer: Paul from Fishers IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Using the part select website, I discovered that 64% of the time, replacing the water pump will fix the drain problem so I ordered that part. I laid the washer on it's back. And was able to unclip the water hoses, detach the pump and install the new one. The parts select website has great instructional videos to help but in this case, the video recommended removing the outer skin from the washer which I found unnecessary.

Leakt water pump

  • Customer: Carl from Newport NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Forget the instruction book, it's too time consuming and it's a knuckle buster. Disconnect all hoses and lay machine on it's back. (Have plenty of rags to soak up the half gallon of water still in the pump). Use pliers to slide back hose clamps on pump and slide off hoses. Use screw drive to snap off clamps holding pump in place. Remove pump. Simply reverse process to install new pump. It nearly was one of my wife's 5 minute jobs she always has on her "Honey Doo" list.

direct drive water pump leaking

  • Customer: gerald from modesto CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.

water leaking from pump

  • Customer: Anita from Globe AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Watched the video, it was so easy, if I had been a little younger it would have been a 15 min job...

Water was not being drained from my washer

  • Customer: Mitchell from Rushville IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After figuring out the shell was not gonna come apart easily, as some videos show for Whirpool, Kenmore.., to gain access to the water pump, I decided to try a trick I'd heard of before and try to get to it from the bottom. Since most washing machines have their water pumps in the front, I pulled it out enough to be able to lean it back against the wall and look underneath. Be very sure you have unplugged the machine from the outlet! Also be sure to support it from falling forward. The hoses and pump were easily accessible from this position.Using the pliers to remove the hose clamps, I could wiggle the hoses off easily. Be prepared for some water to run out, because there will be some in there. After removing the hoses, the clips holding the water pump on were easily removed with my fingers, you might need a screwdriver to loosen the clips. With the clips pulled back, or removed if you turn them 90 degrees the pump should pull off the shaft of the motor easily. A gentle tapping will usually loosen any stuck pump.Once the old pump is removed, line up the shaft of the motor and pump's sleeve with flat sides matching and it should slide on easily. Do not force it, it should slide on easily if lined up properly. Replace the clips holding the pump to the motor. Reconnect the hoses, slide the clamps back into place with the pliers, and you should be ready to Rock-n-Roll. Lower the machine, and slide it back into place. Hope this helps all of those that choose to repair their own Crosley washing machine with a new water pump.

Washer developed a leak

  • Customer: Donnie from Newport TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your repair video and started out like the video suggested but my machine was not assembled like the video so I did it my way it all went well.

Washer leaking

  • Customer: James from BOYNTON BEACH FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I took the cover off the washer off, loosened all hoses and clamps remove old water pump and installed new one.

Washer Leaked At Bottom

  • Customer: Thomas from Stone Mountain GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the instructional video on how to take apart and how to take washer a part and how to install the direct drive water pump. It was very easy to do. also the delivery was very fast. I will be using the site to fix other appiances that I have that is sitting around broken. Thanks for your speedy service and customer service.

replace the impeller

  • Customer: Robert from Trinity FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Put washing machine on it's back giving easy access to the bottom and the impeller. Removed hoses, clamps on the pump and it slips off. Put on new pump, hoses and clamps...job was done. Stood the machine upright and reconnected the inlet hoses with new washers.

Water pump housing leaking.

  • Customer: russ from davie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged washing machine and tilted washer back toward wall. Loosened clamps,removed hoses from water pump and drained water into shallow basin. Pried retaining clips up with screwdriver and lifted pump off of motor shaft. Installed new pump on motor shaft and secured pump with retaining clips. Re-attached hoses and secured clamps. Returned washer to upright position, plugged washer in and ran it through a test cycle with no problems. Watched the video on the replacement of the water pump, so the process was very simple.

Water leaking in floor

  • Customer: Kent from Cushing OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Washer started leaking so I carried it out on the back deck so I could still use it until I had time to fix it, ordered pump, it came in about two days, took about ten minuets to fix and put back in the laundry room. I've had this washer and dryer set for nearly twenty years, I do most things myself, ordering online and having the parts waiting on me when I get home makes things so much easier

Leaking a lot of water

  • Customer: Cesar from Canutillo TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Disconnected water and power supply. Turned washer face up and removed pump. Easy to install just 2 hold down clips.

Direct drive pump was leaking

  • Customer: Larry from Ottumwa IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed washer cabinet. Unclipped pump and disconnected hoses. Put hoses on new pump. Attached pump to drive unit and reinstalled cabinet.
All Instructions for the 11026912691
976-990 of 1,269