11026912691 Kenmore Washer - Instructions

I gave the parts to my wife. Then I took them back and fixed the washer .

The repair went very quick and easy. What made this repair so quick and easy is because of the very prompt and quick shipping of the replacement part from this company. This was my first experience with this company and will always use in the future. I ordered the part one day and the very next day I received the part. Great job to this company!!!!!

I took out the old inlet valve and put the new one in. It was easy

Removed the top part of the electronic panel. Removed the top lid. Removed the old tub springs and replaced them with new ones. Works great and for only $20.00. It beats buying a new washer. Thanks!

used socket wrench with an 8in extension to remove agitayor bolt that was under cap on top part of agitator. was back together in about 15 min.correct parts were shipped in record time.

Removed and took apart agitator and replaced directional cogs.

It was my Mothers washer & did find out the Direct drive Motor Coupling was a little warn & replaced not to hard but took more time to get top off because you have to really get under the top off hood & clips where really in there the vidio showed held on with screws & on this Kenmoore Elite the Clips are under the Hood which does make it alittle bit harder so you have to be careful not to bend up the Hood where all your controls are , But did not solve the issue. Looked at lid switch & it was damaged so now going to Replace it. If this was my machine probably would be a bit easier to have seen it is the Lid switch hopefully this next part will fix the problem.

The job itself was easy in general. It took me a little longer because the ground screw was rusted and I had go figure out how to get it off. I used wd-40 and some serious thought LOL. I want to give credit to Repair Clinic on Youtube and some forums for help determining the problem and being able fix it.

I noticed a leak on the floor. I check the hoses for tightness on the back of the washer and the hoses going to the facets and drain. After disconnecting the hoses going to the washer, facet and drain, I then flip the washer on it's back and examined the underside for wetness. All the underside hoses appeared to be not leaking. I then disconnected the two hoses going to the pump with channel-locks, and I disconnect the two clips holding the pump with just my hand and removed the water pump. I then poured water into the hoses' opening on the water pump itself, and I discovered a slow leak occurring from the shaft area on the water pump. I searched PartSelect and luckily found a water pump that matched. I then installed the new water pump (after receiving it a few days later) in reversed procedures of disconnecting the old water pump. I tested the washer by adding a little bit of water into the washer then switch the dial to spin cycle in order to empty the water inside the washer--no leaks occurred and I was extremely happy.

Unplugged the machine, removed the rear panel and then removed the old water inlet valves. Replaced the water valves with the new one purchased through Parts Select. Installed the back panel on the machine, plugged the machine in and reconnected both the hot and cold water hoses. Tested machine works like a new one again, problem resolved.

Because your video was done so well, it only took about 10 minutes to make the replacement. I was really impressed when my tracking notice was e-mailed it included the link to the instructional video. I will recomend your web site to others.

I followed the instructions outlined on the video for the Lid Switch. It was easier than I thought it would be. Total time was less than an hour. Thank you for the great video.

I was skeptical that this would take less than 15 minutes, but it actually took closer to 5 minutes! (1) Remove the fabric softener cup from the top of the auger by pulling up on the collar as indicated. (2) Pry the cap off the auger with a small screwdriver. (3) Use a long 1/2 inch socket extender (with no socket on it) to unscrew the plastic retainer for the mechanism at the top of the auger. Remove the mechanism. (4) In the mechanism, there's a thin collar holding in the agitator directional cogs. Pry that collar up to remove it. This was the trickiest part. I was afraid of breaking that collar but it survived. (5) Replace the cogs. (6) Reverse the previous steps.

it was so easy to do. i just warch the instructions video clip from partselect.com

Followed the video, as simple as that..