11026862501 Kenmore Washer - Instructions

Watched the video on your website and determined I could easily do the repair. Replaced the part for less than $20.00 including shipping and received it the next day. I ordered the part @ approximately 5 PM and the projected delivery was 1.8 days. To my delight the FedEx truck arrived by 1 PM the very next day and we were up and running within 24 hours of ordering the Direct Drive Motor Coupling. I will definitely use your services again. Special thanks to your video team. I was able to watch step by step how to disassemble and reassemble the washer etc.

I goodgled the make and model of the washing machine and parts select said the solution was to replace the water pump. After watching the viedo my husband and I were convinced this would solve our problem. Instillation was very easy. The toughest part of the project was squaring the frame so we could put the back piece back on. Problem solved, no more water on the floor!

After removing the front, sides and top of the machine (all one piece) the springs were relativley easy to access. I discover one of the brakets that held one of the springs had rusted and would no longer support the spring. I then replaced the bracket and springs. I Re-assyembled the machine and it work as good as new.

This is the first time I've ever fixed anything. I had no idea what I was doing but like the rest of you I decided to man up and get er done myself! I also didn't want to spend 200-300 bucks on a repair guy. So using this site and google. I figured out how to remove the back plate of my washer so I could correctly diagnose the problem...in fact I didnt' even have too remove the back plate to diagnose it because when I started to move the washer I found several broken plastic triangular pieces and a round rubber piece with 6 triangular holes in it. On one of the broken pieces was a serial number of some sort. So I googled what i found and matched what i found on underneath my machine with a part i found on this website which turned out to be the direct drive motor coupling...i figured i was in for a rough battle with the machine but it actually turned out to be pretty easy...in fact it would've been easier had this machine not been serviced before in the past...(i'll get to that later) first step was to remove the back plate...using youtube i figured out how to remove the metal clamps that hold the cabinet to the back plate (you will need a flat head screw driver). Rest was elementary it took me about 2 minutes to remove the back plate after spending probably 30 minutes of research online (i like to make sure i'm doing everything correctly so i watch several videos and do a ton of reading before i mess with anything)*also a side note make sure you unplug the machine before you do anything! Also turn off the water and remove the draining tubes from the back of the machine because you will need to tilt the whole thing on its back failure to do this will result in a watery mess and u could kink the drain tube which will lengthen your repair time like it did with me. Also remove the hot and cold water tubes from teh back...remember that the hot water is always on the bottom memorize where you put the tubes...u can always check which is which by turning the water back on but it will save you sometime* once i got the back plate off i tilted the machine on its back so i could get to the motor and the water pump...there are 2 metal clamps that hold the water pump to the motor. All it takes is a flat head screw driver to remove these clamps once you get the 2 clamps off you can lift the water pump right off the motor its really easy. This exposes the motor which houses the direct drive motor coupling. I inspected what was left of the coupling and if there was any doubt that it was the motor coupling there wasn't anymore because it was clearly broken and the rubber piece that was supposed to sit between the 2 plastic things was gone. Needless to say it was a mess and i knew it was gonna be a challenge to remove the broken coupling. It was surprisingly easy to remove the coupling from the top of the motor compared to the middle of it. There are 2 more metal clamps that fasten the motor in place so it doesn't move around...there are 2 screws that hold these clamps in place. I removed one of them with no problem but the other one was stripped extremely bad i was completely unable to remove it. If you are in this bad boat like i was in i have a solution for you...you only need to remove one screw if you can grab the motor and rotate it enough u can remove the clamp from the metal plate without ever having to remove the clamp at all...its a little difficult and you will have to use a bit of elbow grease to do it but it can be done. Once i achieved this it was a lot easier to access the broken coupling from the middle of the motor. I took the back end of a hammer and evenly jiggled the coupling loose until it popped off...it took a solid 10 minutes tho since the coupling had shattered so bad there wasn't much for the hammer to hold onto. Once i did this i was able to get the new pieces in place...it was a little tricky to line things up correctly but after awhile i was able to get it to fit perfectly...I put the machine back

I pretty much followed the directions in the video, which was very helpful. I didn't have any problems, and although the video was a different model, the parts were similar, if not the same. The parts I ordered were actually better quality than the worn parts I replaced.

I did like the video said about the removal of the control pnl. Now removal of the of the top and front cover was a bit more of a learn as you go to remove all the hoses that go to the fabrix sofner, bleach, and detergent compartments. It was done with the aid of a pair of pliers. There was 4 lines in the top at the back left that has to be removed to finish the cover removal! Now after that it was easy. the rest was like the video. Motor and pump removal simple. I would remember to inspect the inside of the pump to remove any trash that might get wrapped on the impeller.less than hour start to finish and it was a cheap fox and better than buying a new washer!

Have replaced the rubber "dogs" in the agitator before. Washer had an extended service contract that expired in 1986. It just won't die.

Replaced them as I saw it done in the video. It made it a piece of cake!

removed the two screws from the back of the dial bar on the top of the washer. removed original unit, and install the new unit.

disconnect the electrical and tilt the machine far enough to reach under and remove hose clamp.Remove old hose and replace with new one.

I was expecting to spend $100 or more if not having to go buy a new washer. I found your site and I was like "wow" then I found the Video of the intsual. It could not be any more simple. Entire job took 5 min. And under $4 for parts. All I can say is outstanding and thank you

DIAGNOSIS 1) Popped off the agitator cap. 2) Used a 1/2" socket extension driver to back out the plastic retention nut 3) removed the agitator and poured all the little plastic pieces into my hand 4) googled up the agitator assembly by model number, led me to Part select website 5) identified the plastic pieces as "dog ears" 6) ordered new dog ears for just under $4 REPAIR 1) waited 3 days and got dog ears in the mail 2) had a beer and opened the mail 3) inserted the dog ears into agitator assembly according to the picture on Part Select web site 4) had another beer 5) installed the agitator back into the washer, tightened the retention nut 5) admired my handiwork with another beer 6) washed a load of clothes DIAGNOSIS TIME - about 15 minutes REPAIR TIME - about 4 minutes plus 10 more to drink the beers

New hose arrived in 2 days in excellent condition. Repair was fairly easy and fit perfectly. Did notice, however, that new hose was upgraded with a thicker part and a clamp that fit much better. Old hose cracked from repeated shaking where clamp was not tight enough and the hose at this clamp was too thin compared to the new hose. We felt it seemed obvious that the manufacturer must have had many complaints about this original hose. But thank you for your fast delivery and excellent new part.

I gave the parts to my wife. Then I took them back and fixed the washer .

The repair went very quick and easy. What made this repair so quick and easy is because of the very prompt and quick shipping of the replacement part from this company. This was my first experience with this company and will always use in the future. I ordered the part one day and the very next day I received the part. Great job to this company!!!!!