Models > 11026862501 > Instructions

11026862501 Kenmore Washer - Instructions

All installation instructions for 11026862501 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11026862501
1-15 of 1,044
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 484 of 490 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 472 of 501 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.

Water pump leaking when machine used.

  • Customer: Tom from Granby MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 403 of 419 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. Once the machine is on it's back you remove the hose clamps with a pair of pliers and disconnect the hoses. The pump is secured to the motor with a pair of spring steel retaining clips which are easily popped off by hand. Once the clips are removed, the pump is in your hand. Put the new pump in place, replace the retaining clips and hoses, and you're done. This has to have been the easiest repair I've ever done. I wish cleaning gutters was this easy.

spin cycle did not engage

  • Customer: Andrew from SLC UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 176 of 190 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase mounting bolts and took the entire gearcase, shaft, motor, etc... together, out from under the washtub. the clutch slides off the gearshaft with a little fidgeting and the new assembly is easily installed where the previous was. put everything back together... then... spin spin! worked perfectly

top half of agitator did not move during wash cycle

  • Customer: dennis from new stanton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 174 of 198 people found this instruction helpful
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble

Broken Coupling

  • Customer: Hugo from Frisco TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 143 of 151 people found this instruction helpful
Very easy -
1. Removed hoses from the pump
2. Removed Wiring harness from the motor
3. Unscrewed saftey screws from both clamps which hold the motor against the motor bracket.
4. Using a screw driver I easily removed/pryed the clamps from the motor.
5. I then removed the broken plastic coupler from the motor shaft and installed the new one coupler.
6. I did the same thing on the clutch side.
7. I set the Rubber coupler in clutch side.
8. Put motor back on until couplers joined together.
9. Placed Brackets back on Motor (patience here).
10. screwed back saftey screws on clamps.
11. connected hoses back.

Thats it... 45 minutes at most .. Save me from having to buy a new easher. I was convinced I was going to have too until I peeked underneatch the washer and saw the rubber coupler on the ground...

Clothes washer would not spin with more than a couple socks in it. It would barely spin when empty.

  • Customer: Shawn from Longmont CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 101 of 103 people found this instruction helpful
Diagnosing the problem was the toughest part. I originally called a repair man - described to him the problem and he said it was most likely the transmission (gearbox)... of course that is one of the most expensive parts! I asked him if it was maybe the clutch... he said there was no clutch.. only a brake... I knew he was wrong after researching. The fact that the washer would agitate fine and spin very light loads but not spin anything heavy told me it was NOT the gearbox.. or the brake.. it was the clutch.. it had to be... so I called the repair man and canceled the appointment I had made then ordered the clutch assembly. Showed up very quickly. Now to the repair. I realized that I did not have to take apart the cabinet section of the washer.. I only needed access to the bottom. My washer - a 5 year old Whirlpool Gold Ultimate Care II had just a piece of foam blocking off the bottom of the washer... Easy access... I disconnected the hot and cold water and the drain tube. I removed the hot and cold water tubes from the back of the washer also so they would not get crushed when I laid the machine on its back. I unplugged the washer also. The drain tube I left connected to the washer.. I was afaid of it getting crushed while on its back, so I bunched up a large towel put it on the floor and tilted the washer slowly back onto it... the towel was enough of a spacer to keep the drain hose from getting crushed. I used a couple pieces of Duct Tape to hold the lid shut while on its back. I then removed the foam insert on the bottom. Then I unplugged the wiring harness. and a single wire that had a spade connector in the same area. I then removed the clips from the plastic water pump and slid it off the motor (I used Duct Tape again to suspend the water pump up and out of my way while I proceeded) I did NOT have to remove the motor from the gearbox. I used a socket wrench and unbolted the 3 gearbox bolts. I was able to take the whole unit, gearbox and motor out in one piece.. it slid right out (you will have to unscrew the the bolt in the top of the agitator/dispenser shaft - then the gearbox unit with the shaft will slide right out, I did this before I put the washer on it's back) Once it was slid out, I removed the clutch then reinstalled the same way I took it off. The only hard part was the circular wire retainer install for the clutch. It CAN all be done .. I ended up using 2 screwdrivers to put the new retaining ring into the new clutch assembly.. One screwdriver would hold down part of the retaining ring and the other I used to continue pushing the ring into place.. don't give up! You will get it in.. even with normal tools (This was the hardest part of the whole install) It took me 5 minutes with some force and fiddling. I also swapped in the new plastic piece that came with the clutch assembly... you will see where it goes... the old plastic piece looked fine, but I changed it out anyways - it hooks the clutch to the brake system it looks like. After the new clutch assembly was installed I just put it all back together the way I took it apart. One thing I will add was I was not sure if the clutch had to be lined up when I slid the shaft back into the washer.. It does not have to be.. It will align itself automatically. You know when you hear that click/pop when the washer is about to spin?.. well that is that plastic piece engaging with the clutch... there was a piece or two that fell off the shaft when I had removed it.. While sliding the shaft back into the washer I had to just put the pieces back on the shaft before I put the bolt back into the top of the agitator/shaft...

Summary:
Get the washer on its back - unplugged!
remove wire(s) Harness from motor
remove water pump
unbolt 3 bolts holding the gearbox
slide gearbox and motor out as one piece ( a bit heavy)
remove and replace clutch assembly (pay attention to how things are removed)

Done! put it all back together... hope that helps. It worked perfect for me.. and m

Washer wouldn't run

  • Customer: Clint from Kansas City KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 101 of 112 people found this instruction helpful
I removed the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side. To remove the switch, I first detached the wire to the control panel and unscrewed the grounding wire. The new switch drops right in. I had a little trouble getting it in until I realized the washer lid had to be open. A little awkward but once it's in you can shut the lid and then I reattached the wire from the control panel and screwed in the grounding wire. Pretty easy. $20 for the part (with shipping) and 15 minutes. Way cheaper than a repairman.

Water leaking on floor

  • Customer: Stanley from Warwick RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 66 of 71 people found this instruction helpful
I removed the two spring clips that hold the pump and two wire spring clips that hold the hoses. Then I had to pry the pump off the shaft (it was frozen with rust). Then I cleaned the shaft with sandpaper and installed the new pump (which, by the way, came the next day, thank you very much) which made my wife very happy, and I thank you for that , too.

Would not spin unless helped

  • Customer: Ernest from Oakdale CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 63 of 70 people found this instruction helpful
Turned off water supply, disconnected hoses so I could lay on its back.( drain hose also ) have something to catch all the water in. There will be some residual water so have something to wipe it up. Removed agitater, then I removed the spanner nut with hammer and punch. layed it on its back, removed the three mounting bolts that hold the gearcase to the tub support. Removed wire harness and ground wire , pulled gearcase and shaft out . Removed spin tube thrust washer, removed support ring from groove in shaft , removed retaining ring , slid clutch off shaft ,installed new clutch. Take care to watch how parts are removed so that they are installed in proper orientation. Since I had it this far apart I decided I should replace the coupling. I removed the two motor retainers , seperated coupling , pulled both halves off shafts , installed new halves , they go on a lttle tight , newer couplings have metal inserts , aligned coupling halves , inserted together , put motor retainers back on , tightened small screws,done.

Gearcase oil leak

  • Customer: Greg from Hemet CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 57 of 61 people found this instruction helpful
To replace gearcase seals, first disconnect the power cord. Turn off water supply and remove water inlet hoses at washer (safety first). You may want to have a bucket available to catch water that will drain out of the hot/cold and drain hoses. Next, remove top agitator cap, seal and (7/16”) bolt (see diagrams on PartSelect). This will allow the top agitator and cogs to be removed. Grab the bottom agitator and rock it back and forth until it can be removed.
Suggestion: now is a good time to remove and clean the old soap and junk from drain holes in the top agitator and any junk that may be under the lower agitator.
Lay the washer on its right side. You will now have access to the motor, pump, hoses clutch and gearcase. Place a couple of 2X4X(5?) blocks under the tub to support it. Remove the electrical connector from the motor (this is clipped into place) and the two wires that go to the capacitor on the motor.(TIP: don’t put your finger across these terminals, SHOCK HAZARD) Remove the hose clamps and hoses, the two screws (5/16”) on each strap that holds the motor in place, you may have to use a screw driver to pop the straps off the motor. Remove the motor and pump by pushing the tub to the left and move the motor and pump to the right to clear the coupling. If you have not replaced the drive coupling, now would be a good time to order and replace. With the motor out of the way, remove the three (½”) bolts holding the gearcase to the chassis and pull to remove gearcase and shaft. If you are only replacing the drive shaft seal, you do not need to open the gearcase case. Stand the gearcase so the input shaft is facing up, or what fluid is left in the gearcase will come out. One question I see a lot is how do you remove the seal. One, buy a real expensive tool that you will only use once, or take a screwdriver with about a ¼” blade, stick it between the shaft and the seal, gently leverage the seal out while going around the shaft. After the seal is removed, oil can be added thru the seal hole. Understand that different oils are designed for different applications. That said, I used 90 weight gear oil from the local auto parts store, you can add it thru the seal hole. To install the seal, lightly tape it into the seal cavity, then use a socket that is close to the diameter of the seal and gently drive it in.
If you have to replace the top case seal, it will require you to take the gearcase apart. The advantage of this is, if you have an older washer, you can clean out the contaminated oil and sludge and check for wear on the parts, and replace as needed from PartSelect. Here’s a suggestion: if you have a digital camera, take pictures, this will really help when you put things back together.
Now look at the diagram that is provide by PartSelect, remove the clutch, remove the bolts on the top cover, try to keep it level or you may have a mess on your hands. Lift the cover up over the shaft. I found the top case seal very stubborn to remove. Using a small screwdriver, get between the case and the seal and gently pry it out. Replace the seal, again, by using a socket and gently taping into place. There is also a seal at the top of the drive gear that you may want to replace to keep the oil from going up into the clutch. Now its time to clean all of the years of gunk out of the case and gears. When you are ready, fill the bottom half of the gearcase with oil, about half a quart. To seal the case, I used a ultra blue silicone gasket sealer in a tube from my local auto parts store or sealant can be purchased from PartSelect. I used it on the top half of the gearcase case. Slide the top case over the shaft and evenly tighten the bolts. Reinstall the clutch to the gearcase shaft and install into the washer. I found that the motor bearings needed to be lubed, so I used white lithium grease in an aerosol can. Reinstall motor and don’t forget to put the electrical plug back into the motor and the wires that go to the capacitor and pump h

Agitator had a terrible ratcheting sound when running in free-wheel mode during spin cycle.

  • Customer: Adam from Lehi UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 54 of 63 people found this instruction helpful
Removed the gearbox from the drum and removed the direct drive motor from the gearbox. Disassembled gearbox and drained gear oil. Rebuilt the neutral drive assembly with the ordered parts. Cleaned sealing surfaces. Filled gearbox with new gear oil. Sealed and re-installed the top cover to the gearbox. Reattached motor and then reinstalled assembly to drum and clutch (installed new clutch lining at this time as well).

Wouldn't agitate or spin.

  • Customer: Roger from Swainsboro GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 52 of 59 people found this instruction helpful
First, I removed two screws holding the bottom fiberboard panel in place, and the panel, to gain access to the motor, transmission, and pump. Unfortunately, I had the machine tilted to the front, and didn't have room to release the pump. I had to set the machine back up, and get manuvered around so I could lay it on it's back (I was working in the confines of a small laundry room). Once on it's back, I released the two clips holding the pump with a flat head screwdriver, lifted it up and out of the way without having to disconnect any of the piping, then I released the two clips holding the motor, again with a flathead screwdriver, disconnected the wiring plugs, and capacitor wires, then lifted the motor up and out of the machine. I then removed the two bolts holding the motor mounting plate to the transmission. Then, again using a large flat head screwdriver, I pried the transmission coupling half off the transmission shaft, I had to work it up, while turning the shaft, and then the same for the motor half. I then wiped off both shafts, and gently tapped both coupling halves back onto the shafts,
( this is easier using a socket that is just large enough to go over the shafts). Then I reinstalled the motor mounting plate, slipped the rubber coupling onto the transmission coupling half, lifted the motor into place, and rotated from the pump end to line up with the remaining holes on the rubber coupling. I then reinstalled the clips used to hold the motor in place, reinstallation only took thumb pressure to snap back into place, then, I reinstalled the pump, using the same method, and reconnected the wiring plugs and copacitor leads. Lastly, I reinstalled the fiberboard panel into the bottom, and set the machine upright, slid back into place, and reconnected the hoses and electrical, and tested the machine. Worked perfectly.
In actually took longer to disconnect the machine, and get it out and back in, than it did to replace the coupling.

Tub wouldn't turn, but motor would allow it to drain.

  • Customer: Troy from Storm Lake IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 48 of 59 people found this instruction helpful
I took the two screws for the control panel out and tilted it up and back. Then remove the two metal clips which held the outer panel to the back panel. After disconnecting the power and water I tipped the washer on its back. I had to remove two clips to take the water pump off of the motor, then removed the two screws and clips which held in the motor. After removing the motor, I found the coupler was bad. To remove the gearcase, I took out the softener dispenser and removed one bolt to take out the agitator. Under the agitator was a clip. Three bolts held the gearcase to the frame. After removing them, the gearcase pulled straight out the bottom. Replacement was just a reverse process, with the addition of a light coat of grease to the gearcase shaft.

The washer wouldn't spin or agitate.

  • Customer: david from Monroe MI
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 36 of 38 people found this instruction helpful
Frist I disconnected the water lines and power cord. Then I leaned the washer back against the wall. Removed the 2 pump retainers and then the pump. Next removed the 2 screws from the motor retainers and pulled off the retainers and motor. Then removed the 3 bolts from the Gear case. Then removed the cap from the top of the agitator with a flat screw driver. Then removed the bolt from the top of the gear shaft. and removed the auger and agitator assembly. Then removed the gear case from the washer. Next removed the slip ring and then the clutch from the top of the gear case. Next removed the 1/4" screws from cover of gear case and removed the cover. Found the top gear bad. Ordered the new gear and pinion kit. Couldn't find any part #'s to match what PartSelect had. Ordered the gear that they should that fit most washers. The pics they had up looked the same as the one that was bad. Had the new gear in 3 days put it back together and it still wouldn't work right. Took it apart again and looked at it and found a small clip on the bottom side of the gear was upside down. Fliped it over put the gear back in and ran the washer with the gear case out and it worked. Put it back together again. And learned a good lesson always watch how you take things apart for when it's time to put it back together!
All Instructions for the 11026862501
1-15 of 1,044