11026752501 Kenmore Washer - Instructions

Replaced the clutch - works great. HOWEVER - check the drain pump attached to the motor, there was a small sock clogging it up which also fixed the problem. I saved 600 bucks on not buying a new washing machine!!

Parts came promptly. Disassemble agitator as per tutorial video on website. Replace locking "dogs" and reassemble. Cheap, effective fix!

take the cabinet frame out first, take the pump off the motor assembly, take motor out, found the coupling is broken. replace the coupling, put back everything. That's all. Washer start to work immediately.

Youtube video

had to take the entire shell off the washer and then it was 2 simple clamps.

Watched the video on this sight. Fallowed instructions in video and everything went very smooth.

Unplugged, removed water supply hoses, removed drain hose from washer, laid whole washer on it`s back without removing the cabinet, popped clips off the water pump and laid to side, took two screws out of clips that hold motor on and popped them off with a screw driver, unplugged wiring harness and another single wire on motor and then lifted motor off. Then pried the plastic pieces of the coupling off the the motor and transmission shaft. Cleaned debris off motor and washer, replaced plastic piece to the transmission and set rubber part on plastic. Then replaced new plastic piece on motor and set motor back into bracket and put all parts back on in reverse order. I make it sound hard but was a easy job.

disconnected the power, the water supply hoses and took the drain hose out of the wall. Tilted the washer back, undid the 2 clip,took the pliers slid the clamps back. Installed new pump. Put everything back. Done.

Our washing machine "squealed" as it filled. Only the hot water did it, the cold water did not. The hot water came in real slowly, and the machine made a squealing noice and the hose going into the fill valve would vibrate. When I ordered the part, on my order confirmation email there was a link to a video showing how to replace the fill valve. It literally took my less than 30 minutes to replace the part. The only thing that was different on my machine was the screws holding the controls on. Mine were hidden under a plastic cover on the front that I had to snap off. Other than that slight difference in screw location, everything in the video matched up perfect with my machine. With the new fill valve the machine fills in 1/2 the time. We hadn't really noticed how slow it was filling until the squealing noise started. After changing the valve, the difference in fill rate was very apparent. I'm sure the 15 year old valve was full of sediment and minerals. Works like new now.

I followed the video on replacing the direct drive coupling. It was easy to follow and gave step by step instructions for screw locations, fastener and part removal and installation.

The spin cycle was super slow leaving clothes soaking wet at the end of a full wash cycle. Ordered a clutch repair kit, watched the how to video that was e-mailed to me with my order while I did the repair and got it done in about 45 minutes. This was my first true appliance repair outside of maybe a busted fuse or replacing the heating element in a stove. Never thought taking the motor, transmission and clutch out of the washer and putting all back together would be so very simple. Meanwhile my wife is pissed because she thought she might be able to go get a brand spankin new washer...until I fixed the old one. Thanks for saving me some dough PartSelect.

I installed the inlet valve, and it still overflowed. Then I connected the plastic hose from the water level sensor that had came off, to the water level selector and it worked fine

I performed the repair the same as outlined in the video, but I didn't need to tip the washer on the back side. Once I removed the sheetmetal, I was able to swap out the drive coupler, and the new part is a better design than the one that broke.

I followed the directions in the two videos that were provided on your web sight. It fixed the problem and it only cost us about $60.00. We were so thrilled with the results. We were almost ready to go buy a new washer. My wife suggested that we look it up on line and see if we couldn't fix it ourselves before spending the money on a new washer. Was she ever right! Thanks for providing such fine instructional videos.

My sons did it and they said it was an easy fix. No problems to speak of. Used my washer today. it worked like it was supposed to.