Models > 11025862400 > Instructions

11025862400 Kenmore Dishwasher - Instructions

All installation instructions for 11025862400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11025862400
1051-1065 of 1098
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

This washer was not spinning all the water out of clothes.

  • Customer: Sherry from Keenesburg CO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
It was my Mothers washer & did find out the Direct drive Motor Coupling was a little warn & replaced not to hard but took more time to get top off because you have to really get under the top off hood & clips where really in there the vidio showed held on with screws & on this Kenmoore Elite the Clips are under the Hood which does make it alittle bit harder so you have to be careful not to bend up the Hood where all your controls are , But did not solve the issue. Looked at lid switch & it was damaged so now going to Replace it. If this was my machine probably would be a bit easier to have seen it is the Lid switch hopefully this next part will fix the problem.

The unit would no longer spin in rinse mode etc.

  • Customer: Peter from Grinnell IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video on your website and determined I could easily do the repair. Replaced the part for less than $20.00 including shipping and received it the next day. I ordered the part @ approximately 5 PM and the projected delivery was 1.8 days. To my delight the FedEx truck arrived by 1 PM the very next day and we were up and running within 24 hours of ordering the Direct Drive Motor Coupling. I will definitely use your services again. Special thanks to your video team. I was able to watch step by step how to disassemble and reassemble the washer etc.

Washer quit agitating and spinning then after replacing the motor coupling it kept filling

  • Customer: Nathanial from Princeton MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This is the first time I've ever fixed anything. I had no idea what I was doing but like the rest of you I decided to man up and get er done myself! I also didn't want to spend 200-300 bucks on a repair guy. So using this site and google. I figured out how to remove the back plate of my washer so I could correctly diagnose the problem...in fact I didnt' even have too remove the back plate to diagnose it because when I started to move the washer I found several broken plastic triangular pieces and a round rubber piece with 6 triangular holes in it. On one of the broken pieces was a serial number of some sort. So I googled what i found and matched what i found on underneath my machine with a part i found on this website which turned out to be the direct drive motor coupling...i figured i was in for a rough battle with the machine but it actually turned out to be pretty easy...in fact it would've been easier had this machine not been serviced before in the past...(i'll get to that later) first step was to remove the back plate...using youtube i figured out how to remove the metal clamps that hold the cabinet to the back plate (you will need a flat head screw driver). Rest was elementary it took me about 2 minutes to remove the back plate after spending probably 30 minutes of research online (i like to make sure i'm doing everything correctly so i watch several videos and do a ton of reading before i mess with anything)*also a side note make sure you unplug the machine before you do anything! Also turn off the water and remove the draining tubes from the back of the machine because you will need to tilt the whole thing on its back failure to do this will result in a watery mess and u could kink the drain tube which will lengthen your repair time like it did with me. Also remove the hot and cold water tubes from teh back...remember that the hot water is always on the bottom memorize where you put the tubes...u can always check which is which by turning the water back on but it will save you sometime* once i got the back plate off i tilted the machine on its back so i could get to the motor and the water pump...there are 2 metal clamps that hold the water pump to the motor. All it takes is a flat head screw driver to remove these clamps once you get the 2 clamps off you can lift the water pump right off the motor its really easy. This exposes the motor which houses the direct drive motor coupling. I inspected what was left of the coupling and if there was any doubt that it was the motor coupling there wasn't anymore because it was clearly broken and the rubber piece that was supposed to sit between the 2 plastic things was gone. Needless to say it was a mess and i knew it was gonna be a challenge to remove the broken coupling. It was surprisingly easy to remove the coupling from the top of the motor compared to the middle of it. There are 2 more metal clamps that fasten the motor in place so it doesn't move around...there are 2 screws that hold these clamps in place. I removed one of them with no problem but the other one was stripped extremely bad i was completely unable to remove it. If you are in this bad boat like i was in i have a solution for you...you only need to remove one screw if you can grab the motor and rotate it enough u can remove the clamp from the metal plate without ever having to remove the clamp at all...its a little difficult and you will have to use a bit of elbow grease to do it but it can be done. Once i achieved this it was a lot easier to access the broken coupling from the middle of the motor. I took the back end of a hammer and evenly jiggled the coupling loose until it popped off...it took a solid 10 minutes tho since the coupling had shattered so bad there wasn't much for the hammer to hold onto. Once i did this i was able to get the new pieces in place...it was a little tricky to line things up correctly but after awhile i was able to get it to fit perfectly...I put the machine back

Washer didn't spin one day. Just made a clunking noise.

  • Customer: Stephen from Middlesex VT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I first thought that the fan belt came off. Got the cloths out of machine, and tipped on over to look under, where I discovered that there was no fan belt. Looked online for answers, and found that machine was direct drive. Looked around under machine for something damaged or broke. Saw the direct drive coupling was cracked into three pieces. Ordered the part I was 95% sure I needed, and it was at my house in less than 48 hours. Watched a video on how to replace the direct drive coupling. This was amazing and easy to use information. Made me feel like a pro. The video covered everything you could imagine for the repair, step by step. Machine runs now as good as new.

Washer would not spin or agitate

  • Customer: John from Idaho City ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1) Unplugged power to the machine. 2)Disconnected the water inlet hoses and the drain hose. 3)Placed the washer on the front of the cabinet. 4) Moved the washer to an area large enough to allow it to be laid down and worked on. 5)Removed the sound deading panel from the bottom of the washer. 6)Disconnected the electrical plugs from the motor. 7)Disconnected the two hoses to the pump. 8)Removed the two strap retaining bolts from top of the motor. 9) Removed the two motor retaining straps. 10) Removed motor and pump assembly from the transmission. 11) Removed the broken drive coupler and replaced it with the new coupler. 12)Reassembed in reverse order. Wish I had seen the brake repair vidieo before this repair was done. It shows how to remove the trasmission and motor asembley as a unit.

No longer spinning

  • Customer: Terri from Sahuarita AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Repair went really well thanks to the video PartSelect had posted with the drive motor coupling. It showed me how to take machine apart to replace the coupling. Loved the step-by-step instructions. Made it so easy for my son and me to do together and I am a female.

washer would not agitate or spin, even after replacing coupler

  • Customer: GEORGE from GERMANTOWN KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Found input to gearcase deformed, so new coupler slipped under load. Replaced gearbox. All function restored, but machine banged harshly during spin. Discovered that "skid plate" had shifted during gearbox replacement. Remounted skid plate carefully with pry bar, correcting vibration.

would not agitate

  • Customer: art from denver CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
searched the internet for the problem, saw video on you tube, bought the part & repaired/replaced the couplers. You have to make sure the couplers are all the way on the shafts, so the washer can be reassembled correctly. After it was reassembled, the machine would not go through the cycles. Apparently unrelated, the lid switch had become defective. I ordered the part & fixed the problem. That repair is also on you tube.

Drum not spinning!

  • Customer: Lew from Saint Simons Island GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the on site video.....Did everything except removing the cabinet....Laid the washer on the front side and did the repair underneath in less than 30 minutes.....I might add the new coupler is much better than the original which was all white plastic....The new part was nylon and had metal inserts. The original had no inserts. Some have said the original part that had the two flat sides would just round out causing the drum not to agitate or spin. Mine just broke in half. I don't see this new part breaking or rounding out the metal inserts.....I might add Whirlpool OEM part was costing much more and with a 5 business day wait on delivery....Parts Select 1.8 day was advertised and it came in two days.....You won't go wrong doing business with Part Select.

Two out of six interlocking spokes of the plastic flex-coupling hubs had broken off due to years of service. Contributing factors were running heavy bath towels.

  • Customer: Will from Arroyo Grande CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Was going to "...just take it apart and fix it" as my career covered being a mechanic, machinist and vocational instructor for over 35 years. Just in case. I decided to visit the PARTSELECT" website for "How-To" guidance. There I fund excellent troubleshooting guidance, including root-cause analysis in % of likeliest cause(s). This was followed with a brief step-by-step descriptions of "How-To" activities, including necessary tools. Best of all was the short instructional video, showing exactly how to go about the repair in a safe and systematic manner. As a former instructor, I am truly impressed by the quality of the material and service this website offers! It made my job so much easier, and consequently it was well done in no time. I urge every customer to follow the excellent guidelines and strongly recommends this site to others. Total cost of my repair was $11.00 for the part, plus shipping; saving me a bundle and possible grief and frustration! The website gives great customer service off- and on-line with follow through by courteous personnel. Thank you for the superior customer service and level of support at every step!

Lost the spin cycle and had a rumbling noise.

  • Customer: Brent W from Amelia OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I performed the repair the same as outlined in the video, but I didn't need to tip the washer on the back side. Once I removed the sheetmetal, I was able to swap out the drive coupler, and the new part is a better design than the one that broke.

Drum wasn't spinning during spin cycle.

  • Customer: Douglas from Blue Point NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the directions in the two videos that were provided on your web sight. It fixed the problem and it only cost us about $60.00. We were so thrilled with the results. We were almost ready to go buy a new washer. My wife suggested that we look it up on line and see if we couldn't fix it ourselves before spending the money on a new washer. Was she ever right! Thanks for providing such fine instructional videos.

washer would spin intermittently

  • Customer: Kristine from Los Angeles CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Parts Select is AMAZING!! It directed us to the correct parts. Ordering was easy. But the best part was the videos. The step by step instruction was a godsend. We followed it, paused it, compared it, did it. We had to battle grease and tight quarters, but got it done. The machine works good. We spent about $65 as opposed to $400+ for a new washer. Great website.

Washer stopped agitating and would not spin water out

  • Customer: Deborah from Brunswick OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
When my 13 yr old washer stopped working the timing was not at all good to spend money on a new one. I have two of my children getting marriied within the next year and funds are tight. I decided to troubleshoot it myself online by googling my problem. I found out what I thought would be the parts I needed, I took a chance and ordered them. The bonus was the videos that you emailed me with the complete installation instructions. I am a banker and a 53 yr old woman ...not exactly a handy man. With your videos I was able to fix my washer by my self for just the cost of parts...so my wedding budget is still in place. I highly reccommend PartSelect for anyone...cause If I can do it anyone can do it! Thank you PartSelect

washer did not work after replacing agitatior parts

  • Customer: kimberly from Grass Valley CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I was thrilled that the agitator parts were so easy to replace, but that didn't totally fix my problem. I looked underneath the washer and found black rubber shavings from a worn part and looked online and found that the problem was most likely the Direct Drive Motor Coupling. I watched the video and ordered the part. The coupling was actually broken. After replacing the part, the washer works great...better than it has in years. I think I will work on our dryer now.
All Instructions for the 11025862400
1051-1065 of 1098