Models > 11024872300 > Instructions

11024872300 Kenmore Dishwasher - Instructions

All installation instructions for 11024872300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11024872300
1,216-1,230 of 1,271
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

not spining at full speed

  • Customer: mike from la porte city IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
this repair was really easy to do and did not take long. i used the video on whirlpool.com made it really easey. washer works like new.

The agitator was not working in the washing machine.

  • Customer: BOBBI from SOUTH AMHERST OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I used the flat screwdriver to pop off the top of the agitator. then I used my socket wrench with extension to remove the bolt holding the top of the agitator to the bottom agitator. I pulled out the small piece that holds the agitator cogs. The agitator cogs were sheared off. I used my screwdriver to remove what was left of them, cleaned up the unit, then installed the new cogs. Re-insert the piece into the agitator unit and tighten the bolt back. Popped the lid back on top and ran a load of laundry to test. It works perfect! Although the teeth are pretty worn on the agitator as well, so I'm looking to buy a whole new agitator unit next. Very easy fix!!

no spin dry

  • Customer: Walter from West Palm Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
... exactly as shown in the video in addition to shutting water, removing hot & cold lines & waste tube. I was amazed at how fast the parts were delivered in two days regular shipping. Machine now purring a wifey happy once again! Thanks for the great service & video! I recommend PartSelect highly! WSD

Tub was spinning only part time. Had to have help getting started

  • Customer: Kingsley from Ewing IL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installed new clutch assembly and while I was at it replaced the Motor Coupling. Actually, I had a good time doing the repair. I am almost 80 years old, so had to have help laying the washer on backside. Got a small stool from which to work (back problems). The only thing I found the least bit difficult was reinstalling the retaining clip for the clutch assembly. The rest was a piece of cake. Were I to do the same repair now, it would take less than 30 minutes. Washer works like new now. Very proud of what I was able to accomplish. Of course, need to watch the repair video so you will know where to start.

Bad Motor Coupler

  • Customer: Hilary from Gainesville FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
So, the instructional video was great but be warned that you REALLY need to hammer the part into place. Basically hammer it into place so that the end of the shaft that it goes on is flush with the plastic piece of the coupler on both ends. Otherwise, you'll put the washer together and run a load and it'll squeal and smell like burning rubber. We had to take it apart like 3 times before we got it on there securely enough. We would then run an empty load and it would be fine but as soon as we would add clothes the squealing and burning would ensure. So, my advice is to hammer it in well and save yourself the time and struggle!

Washer woulp not spin, brake cam driver not like video

  • Customer: Jody from Elk Creek CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
changed parts easily, following the video. Problem was the BRAKE CAM DRIVER, the plastic piece that fits around the shaft near the drum. The old one was visibly torn up, the pegs worn off, the whole thing worn down. The problem with the repair was the video showed an "E ring" holding it on and my washer had no E ring, had nothing hold it. It just sat there. Installed it anyway, although I was worried it was too loose. Sure enough there was a problem. it spun initially then started that ugly clicking noise. turned off washer immediately, disassembled again, and prayed. I found a large flat washer to take up the slack between the clutch and the plastic brake cam driver, reassembled, tightening the nuts a fair bit tighter than before. both the nuts on the transmission and the nut on top the agitator. works perfect!

direct drive motor coupling

  • Customer: Eugene from Chiefland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

The tub would not spin during the spin cycle. I diagnosed that the door switch was functioning. And through some reading on the internet, found out it was the motor coupling. I replaced the clutch assembly strictly as preventative maintenance.

  • Customer: Jorma from Saint Cloud MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

Washer full of water not draining

  • Customer: James from Port St Lucie FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

The washing machine started making a clicking type noise and would not drain after the rinse cycle completed.

  • Customer: Larry from Buffalo TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.

Tub will not spin

  • Customer: Rick from Terre Haute IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.

Motor Coupling Broken

  • Customer: Jeff from Nicholasvile KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.

Washer would not spin. Coupler was the problem.

  • Customer: Joey from Murrieta CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video they provide was very easy to follow. The only difference from mines and the video they provided was the top portion. Mines was held by two Phillips screws on the switch housing. The top pulls forward. Everything else went accordingly. Take off switch plugs, take off washer cover, unplug the vacuum line, replace coupler and reinstall. Only thing that took up time was getting water off the floor when I pulled the vacuum line. Use a bucket or do it outside.

Intermittently the spin cycle would not empty the tub fully

  • Customer: Robert from York PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off, let me say two things, this was my very first washer repair and the installation video was excellent.

Few things though ..... The first thing I noticed was the old parts I removed did not look that bad to me. I was starting to wonder if I was wasting my time. However, its apart now I'll continue on. I had a hard time properly seating the new couplings on either end correctly. They were VERY snug. What I ended up doing was getting a 20mm deep socket that fit perfectly onto the coupling and with a hammer gently, (and I underline gently) tapped the new parts into place. That fixed that problem. I also had some minor difficulty putting the cabinet back together, but nothing earth shattering. The cabinet fits on top of the frame, not under. And lastly, the small clips that hold the console on were not very reusable afterwards so I'll need to order a new set of them sometime.

All-in-all it was a fun repair that didn't take me too long and I saved quite a bit. I definitely would do it again if necessary. I've done about 5 loads of laundry since and everything seems to be working great so far.

- Bob

Washer was not spinning.

  • Customer: DEREK from BARNHART MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
It was simple, unbolted the inside laid it down on its back, took four bolts how and replaced parts and reversed the steps. It was super easy and You guys was on top of the shipping. Wife is happy! saved $500!!!!!!
All Instructions for the 11024872300
1,216-1,230 of 1,271