11024642300 Kenmore Washer - Instructions

The most difficult part was aligning the two sides of the coupling. Disassembling the motor from the transmission was a snap. The replacement coupling was of higher quality than the original. It had metal bushings in the center holes, where they interface each driveshaft. The original did not. It was plastic.

It went very easy and the part was right very easy job to do saved a lot of money thanks to you thanks a lot

The repair went very well as per the video, however the metal reinforced coupling only went onto the shaft half way. To ensure the coupling was flush with the top of the shaft I has to use a hammer and tamp the coupling onto the shafts. If you left it halfway on the shafts there was no room for the rubber spacer between the couplings. Other wise it operates very well.

remove top cap on agitator, remove seal from inside of agitator tube( seal looks like garbage disposer stopper)now you see top of bolt head, use 7/16 socket with a 12 inch extension, hold bottom of agitator to keep it from turning while removing bolt,pull up on agitator top to remove, remove assembly that holds the cog's,slide off retainer ring, replace with new cog's, (when reassembling match pins in bottom part of agitator to slots in top part of agitator.)install bolt, install seal(use some laundry detergent so it slides in easily),put cap of agitator back on. that's it

My 15 year old daughter did the repair.

You guys are "Awesome" I wish I had known about your site and watched the video's first!!! When my washer started acting up, I tore it down to parade rest trying to figure out why it wasn't spinning! Then I discovered your web site searching for help. Anyhow, it identified my problem, I watched the video on the most likely cause (the Direct Drive Motor Coupling), checked it out, and discovered one of the couplings was cracked and rounded out..... Thanks to you, the washer's fixed and I can't Thank you enough! Sincerely, Terry Kuster P.S. Everyone will know about your Web site. Thanks again!

After watching the video that came with the parts, it was straight forward, very well informative.

Put washing machine on it's back giving easy access to the bottom and the impeller. Removed hoses, clamps on the pump and it slips off. Put on new pump, hoses and clamps...job was done. Stood the machine upright and reconnected the inlet hoses with new washers.

The unit would not fill with water. My wife had been complaining that the tub had not been filling completely before the filling completely failed. If I switched the water level to another setting and then back, it would run fine for just one cycle. That's why I suspected the water level pressure switch. It was a very simply switch out, requiring just a philips screwdriver and popping the control panel on the top open (thankfully not messing with the main cabinet). It was replaced and reassembled within just minutes!

well ttook 2 screws out of the top unhook the wire to door pulled front back away from back and there it was easy as apple.

1. visited web site followed path for symptoms, identified part ordered 2. Dismantled Washer, removed motor, replaced coupling and re-assembled. 3 Tested outside to confirm working order before returning washer to inside location 4. Moved washer back inside.

I followed the step by step instructions on the computer stopping and starting the program as I went. Thanks Partselect

Just watched the video provided by parts select and then went to work. Excellent video. If I had been better mechanically inclined it would have been much faster. Thank You Parts Select! Also fast shipping.

I watched the video that PartSelect provided on their web site. The instructions were very precise and easy to follow. I watched the video twice and just followed the instructions. I would highly recommend this approach to washing machine repairs. It certainly saved me a lot of money.

took top agitator off, cleaned it (needed anyway), replaced agitator directional cogs, replaced washer (old one was too soft to reseal) upon bolting back together. Oddly the repair kit on this website does not include a washer - I only bought the cogs - it turned out to use the same washer I use on my kegerator