Models > 11024622300 > Instructions

11024622300 Kenmore Dishwasher - Instructions

All installation instructions for 11024622300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11024622300
1,246-1,260 of 1,363
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water pump leaking

  • Customer: stephen from fort ann NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Had to unhook and move dryer out of way.Then unhook washer and move so I could tip it over onto its back.Removed retainers and pump, unhooked hoses.Installed new pump then put everything back place. Probably done in less than an hour.Biggest part of job was moving machines .

Leaking Water Pump

  • Customer: Paul from Miton DE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I disconnected the washer from the water hoses and unplugged it. I laid it down on its back and the pump was right there on the bottom front. There were no clips holding the pump. With a pair of Channel Locks I disconnected the two hoses from the pump. I had to pry it off using a screwdriver. The pump shaft was rusty from the water leak so I wire brushed off. I put the new clips I ordered in place and pushed the new pump on. I then snapped the back clip on first because it was easier with a little tilt of the pump. I had to use my screwdriver to put the outside clip on. I reconnected the hoses put the wash back upright hooked up the water hoses and plugged it back in. I turned on and no leaks and is working good.

Washer was not spinning, but making a loud spinning noise.

  • Customer: William from Sonoma CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Disconnected power. Disconnected hot and cold, and drain hoses and placed in a plastic bucket. Pulled cover off the washer. Tilted washer onto its back. Removed 2 clips holding the pump. Disconnected wire harness from motor and removed 2 clips holding motor starting with lower clip. Removed a screw from the upper clip used for shipping. Set motor aside and removed broken pieces of the motor coupler from motor and transmission. The replacement part had a metal sleeve in the center of each white plastic ring. The old part did not. This required tapping the new ring onto both the motor and transmission shafts with a socket and makes for a tight fit. Reversed the process to put everything back together. Some alignment might be necessary to place motor to transmission. I recomment wearing thin work gloves to avoid nicks from sharp edges. I didn't. Washer is spinning again and sounds a lot better.

Washer would not always spin

  • Customer: Donald from Metter GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I purchased the part from PartSelect because it was very reasonable and it was OEM part. I have never replaced this kind of part on a washer so I figured it would take me a while. But PartSelect supplied a video showing the entire repair and that was the only reason I did not struggle with the repair. I will definitely buy any appliance parts I need in the future from PartSelect. Thanks Don

washer would not spin or agitate.

  • Customer: Gerald from White Cloud MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
electric unplugged, removed water lines. two screws on back of control housing removed, tilted housing back, removed two clips on top of washer housing, removed body. tilted washer backward, removed brackets on water pump and electric motor, pulled motor off and removed broken parts on shaft, replaced with new parts. Lining up motor shaft to washer was a bit tricky but time and patience got it togather. replaced brackets on motor and water pump. put washer upright and put body back on the body has to be set on guides correctly or will not set right. replace clips andtilt top down and screw it. hook up water lines, and electric.

bushing between motor and transmision broke

  • Customer: NAN from mt carroll IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched the video on line showed how to do it took about 45 min no problem

burning smell

  • Customer: Lindsay from Loves Park IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the videos that were very helpful and repaired it my self with no problems its fixed and running like new i took a little extra time to clean all of the washer since i had it apart any ways so the time to fix it was probably was a little shorter i would like to thank part select for all there help and videos it made this job so much easier.

The washer was making noise and was leaving the cloth dripping wet at end.

  • Customer: Kenia from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Before I even watch any partselect videos to do the repair, which I should of from the very beginning, ah, ja, ja, I had already disassembled the back panel "my way" to the washer and trouble shooting the washer with my wife's help. While she tilted the washer backwards, I looked under and we found that the noise was coming from in between top of the motor where the direct drive motor coupling is located and the clutch assembly came together which I learned along with names and functions after watching the partselect installation video. Nice! Once I received the part it took me like 45 minutes to put all back together. Took loose two screws to clips holding the motor, pulled motor of mounting bracket finding the broken piece, replaced it, recouped reinstalling motor onto the motor bracket, clip, clip the two little screws and walla, got the wife her washer back, at bed time rewards, peace of mind the rest was history... Thanks PartSelect for awesome videos and great customer service!

agitator,drive motor coupling,water pump 3 problems

  • Customer: judy from lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch the you tube, and try to fix it by myself,to save money, and moving trouble.this is my first time fix a big machine like this,I was a little scare, but after I saw the youtube about how to fix the washmachine,I start to give a try.it take little bit more time for me to figure out ,but I finally made it. now I can wash my cloth now, and perhaps fix washmachine for my exrat income.( message sharing from an asian 58 yrs old lady, sorry for unable to show step by step due to English not very good)

washer was squealing during wash and spin cycle

  • Customer: George from Cole Spring KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video and instructions included with part. At first we did not think the repair was successful, but after several small loads were run, squealing stopped. The washer is 16 years old and so far is running like new. We certainly appreciated the great customer service. The part was delivered in less than 24 hours.

noise caused b y broken coupler between motor and transmission during "spin" and not spinning

  • Customer: John P from Brazil IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed motor and broken coupler... installed new coupler and replaced motor. also removed pump to inspect for sock, etc. that that might have caused coupler to break.. ADVICE: Look for how-to video on YouTube first. Remove outer cabinet according to video by first removing the top control panel and then remove the outer cabinet which exposes the motor and pump. This way you will not have to tip machine up/back and work under it. This repair is made easily by first removing the outer cabinet.

Washer would not spin

  • Customer: Mark from McCall ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I followed the instructions from a YouTube video, just do a Google search for the make, model, and what the problem is and several videos will come up to pick from. Everything went just as described in the video, took about 10-min to take the motor out, a couple of minutes to replace the broken motor coupling, and another 10-min to put it back together - slick.

Pumps but won't spin, leaks, top of agitator doesn't move

  • Customer: Kenneth from Talbott TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My repair was successful but was not as easy as some have reported. I needed to replace the coupler, but when I tried to remove the pump from the motor, the shaft was rusted and wouldn't budge. I pried and wiggled and used WD-40 to no avail. I ended up taking off the motor and pump as a unit. After replacing the coupler and reassembling the washer, the water pump leaked, probably as a result of all of the prying. To get the water pump off, I had to cut it into pieces, using a hack saw. Even when I got down to the end, I had to peel pieces of plastic off of the rusted shaft. I then had to file and sand the shaft to get it so that it would fit into the new pump. After putting the washer together again and running it through its cycles, I noticed that the top half of the agitator was not turning. I then ordered and installed the agitator repair kit. Through all of this, my orders were all correct and arrived in amazingly fast times. The videos were all very helpful. Even though it was a trial a times, I still saved a pile of money.

Washer would not spin. Coupler was the problem.

  • Customer: Joey from Murrieta CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video they provide was very easy to follow. The only difference from mines and the video they provided was the top portion. Mines was held by two Phillips screws on the switch housing. The top pulls forward. Everything else went accordingly. Take off switch plugs, take off washer cover, unplug the vacuum line, replace coupler and reinstall. Only thing that took up time was getting water off the floor when I pulled the vacuum line. Use a bucket or do it outside.

Intermittently the spin cycle would not empty the tub fully

  • Customer: Robert from York PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off, let me say two things, this was my very first washer repair and the installation video was excellent.

Few things though ..... The first thing I noticed was the old parts I removed did not look that bad to me. I was starting to wonder if I was wasting my time. However, its apart now I'll continue on. I had a hard time properly seating the new couplings on either end correctly. They were VERY snug. What I ended up doing was getting a 20mm deep socket that fit perfectly onto the coupling and with a hammer gently, (and I underline gently) tapped the new parts into place. That fixed that problem. I also had some minor difficulty putting the cabinet back together, but nothing earth shattering. The cabinet fits on top of the frame, not under. And lastly, the small clips that hold the console on were not very reusable afterwards so I'll need to order a new set of them sometime.

All-in-all it was a fun repair that didn't take me too long and I saved quite a bit. I definitely would do it again if necessary. I've done about 5 loads of laundry since and everything seems to be working great so far.

- Bob
All Instructions for the 11024622300
1,246-1,260 of 1,363