Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11024422300 > Instructions

11024422300 Kenmore Washer - Instructions

All installation instructions for 11024422300 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11024422300
946-960 of 990
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The washing machine basket wouldn't spin

  • Customer: Kali from Missoula, MT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Remove the cover of the washer, pull out motor, pry out motor coupler, replace. May have to hammer with a rubber mallet to get it on. Replace motor and washer cover. We also replace the water pump. It wasn't broken, but since we had the washer torn apart, decided to replace it as well. There are lots of YouTube videos to help you out.

would not finish agitating to go into first spin cycle

  • Customer: Ralph from Peoria, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch video, follow instructions. Very easy.

no spin out of water in drum

  • Customer: james from dumont, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video on the web site and repair was amazingly easy. I have two of these machines, and this same part went bad about 1 1/2 year ago, so this time i was ready for everything. Took everything apart, got rid of old broken part, replaced with new, and Bam, washer back up and running, less than 30 minutes, I am limited on space in my basement, so i didn't turn machine on its back, i did it in the upright position, just utilized some wood blocks to hold the motor during part change, and a hand spring clamp to hold pump and hoses out of my way after removing the clips that hold it on. It's not rocket science, if i can do it so can you. Good luck

drip from the front of the washer

  • Customer: Martin from Lawrence, KS
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First I tipped the washer forward and placed a plastic milk crate under the rear of the washer to support it . Then tipping the washer back. I placed two car jack stands near the front to support and level the machine. Now I had enough room to look under it to see where it was leaking. Right away I could see a drip coming from the pump in the front of the washer. I removed the two water hoses. Then with a screwdriver popped a clip on the top of the pump and one on the bottom. The pump slid easily off . Slide the new pump on and reverse the process

Loud screaching noise occured during use

  • Customer: William from East Northport, NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed written instructions after viewing repair video. Would have been helpful to know how far onto shaft each drive piece needed to be placed. I should have noted old piece placement, though if this was noted in instructions it would have been reassuring to know what is the proper placement. I also placed machine on its back to align the motor and transmission after new parts were installed on each.

Washer inlet clogged.

  • Customer: Anthony from Hewitt, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We started to get water hammer in the pipes when ever the washer was set to cold? Looked it up here and figured the inlet was about to go out, ordered the part, 2 days later, brand new washer, no more problems. Local repair would have cost us at least $100.00, part was $25.00 shipped, videos are awesome tools, PartsSelect Rules!!!

My washer stopped spinning.

  • Customer: Jacob from Champaign, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I researched the troubleshooting on PartSelect.com and determined the clutch was going out on my direct drive Whirlpool washer. I ordered the part, found the instructional video that actually had my exact washer being worked on, I followed all of the steps of replacing the clutch and in a snap, my washer was spinning. I've worked in apartment maintenance for years and PartsSelect.com has always been my only resource for appliance parts and repairs. The prices are great (I've compared most parts websites and 8 times out of 10, partsselect.com is cheapest), the shipping is extremely fast and the parts are alway right. Great site!!!!

Washer shook in the SPIN cycle.

  • Customer: Mark from Dagsboro, DE
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

Washer was not agitating and no spin cycle

  • Customer: Michael from Doylestown, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The repair was easy and the video tutorial was great. That was the easy part. I also had to replace the drain pan and getting it in and out of the pan is no easy task. Plus when you have not moved the washer in 10 years there is some cleaning to do. I would not hesitate to do it myself again. It cost me $20 and some sweat equity.

Machine wobbled during spin cycle. Appeared to have some loosened part in the rear of the machine (noted some flexing on the front of the cabinet during spin).

  • Customer: Jonathan from Brandon, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.

The tub suddenly stopped moving after the final rinse, before the final spin.

  • Customer: Raymond from Chagrin Falls, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video to get a good idea of the procedure. I followed the instructions to remove the cabinet but kept the washer upright on its base. I left the water feed hoses attached to the wall spigots, but turned them off. The pump was rusted onto the motor shaft so I left it there. I unhooked the pump hoses from the pump so I could remove the pump and motor as a unit. The plastic coupling ends pulled off the motor and gearbox shafts easily. The new coupling ends have metal inserts which are a tight fit on the gearbox and motor shafts. To maintain the original alignment it's important to drive them fully into place. I greased the shafts then tapped the coupling ends on with a hammer and drift. The drift was a metal tube, inside diameter slightly larger than the shafts, but small enough to bear on the metal inserts, not on the plastic. My diagnosis was wrong - the original coupling was in good condition, but the clutch had failed.

washing machine cycle stopped completely after wash cycle.

  • Customer: james from madison, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I dipped most of the water out of the machine because it was heavy, and needed to be moved out from wall. Always unplug the machine, and cut the water valves off. I pulled the two plastic end caps off the control panel, unscrewed the two philip screws from the ends of the control panel, flipped the control console up, and backwards. unscrewed the ground wire screw in the back. popped two"S" clamps holding the metal cabinet to the back panel. tilted the metal cabinet forward, lifted it from around the tub, unscrewed the two screws holding the switch, and ground wire. replaced the switch. oh, you must unplug the connector before tilting the metal cabinet. reverse the procedure. make sure you plug the connector up before you pull the control panel back into place. I cleaned, and vacumned the dust and dust inside the machine. so it took a little longer than usual. about an hour. Very easy job, but kind of cramped quarters for me. machine runs like new.

Water dripping slowly into washer tub

  • Customer: Paul from Redwood City, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Looked at the video instructions on the web site, then noticed my model was slightly different. Switched to YouTube. Searched "Water Inlet Valve Replacement Whirlpool Washer". The repair was faster than advertised (40 minutes total). Less time than waiting for a repair person... Very good delivery service from Part Select. Will buy again!

No spin on spin cycle

  • Customer: Thomas from Port Jervis, NY
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Easy, If your drive block has an open top, it's worn. Look at a picture of a new drive block and compare. If it doesn't match, then you need a new drive block. Note: Also check the drive clutch and clutch liners or pads...they may be worn. In my case it was the drive block this time. So to start, take off the fabric softenner dispenser in the center of the washer. Then pull out the seal. then remove the bolt. and pull off the agitator assembly. after that tap off the lock nut with a punch and hammer or if you have the special spanner wrench tool, use that. Once removed, pull out the inner tub and then pull the drive block off the shaft. Put the new drive block on and reverse the procedure from there. Tap the lock nut tight with the punch and hammer while re-installing. I'm so glad I did this repair. $15 is so much better than just giving in and buying a new washer!!!

Water would not flow on rinse cycle

  • Customer: Kenneth from St. Ann, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed housing from washer to gain access to bad water inlet valve, removed old inlet valve, installed new valve using your instruction video and now the washer I bought back in 1994 works like new. Thanks PartSelect for your great service and FAST DELIVERY of part.
All Instructions for the 11024422300
946-960 of 990