11022692100 Kenmore Washer - Instructions

I watched the video on the Partselect website. Appled the same technique for my machine and the repair was just as easy. Unplugged the washer, removed two screws from the top panel, flipped it up and removed the two brackets that hold the cabinet in place. Removed the cabinet, the pump is right in front held on by two clamps. Removed the clamps, unhooked the hoses, put the new pump in attached the hoses and the clamps. I then put the cabinet back together and the repair was complete, wash machine is running again with no leaks.

I watched the video on the website on how to repair this and followed it. The repair went quickly. I spent more time moving the washer in and out of the location it was in than the time it took to repair.

Remove the outer washing machine housing. Close-up inspection located the leak source. The water pump was removed by popping off the upper and lower metal brackets, then removing it from the two rubber hoses with their pinch clamps. Ordering a new part was easy on your web site, and it arrived in 2 days! I reversed the process, with the smaller hose's pinch clamp hard to manage with simple pliers, but doable with persistence. I LOVE my 23 yr old whirlpool washer, and don't want a newer model, so thanks for making repairs doable for an old lady!

I pulled the dispenser cap off the top of the agitator, then removed the water tight cap from inside, then used a socket and extension to remove the bolt and the top portion of the agitator. The cogs and holder easily came out of the agitator, then the black hold down ring was slipped away from the cogs and the cogs then easily were removed and replace with the new ones. The black hold down ring was then slipped back into place to hold the cogs in and the agitator was reassembled. Works perfectly now and only cost $8.95 and three days for shipping.

I watched the online video and followed the instructions,The only problem I had was getting the pump off the drive shaft it had rust built up,but it worked fine and was shipped as promised

I simply watched the video that was on YouTube for this site. It was dead on with my washer and super easy to do. The step by step was just awesome and easy to follow. The repair took just over an hour and I even cleaned the entire inside of this 12 year old washer which was pretty cruddy. The washer now spins great and works like new again. All for about $50. Thanks.

A word to the wise watch the repair video first guys and save an hour or 2 of aggrivation. I saved a couple hundred bucks instead of having the repair guys do it. It was easier than I thought. Machine runs like new again. Thanks Partselect. L.A.B. Rocland, Mass.

Disconnect washer from all connections and slide away from the wall far enough to give clearance where you can tilt the washer and lay on it's back. Remove old pump and replace with new pump, then reconnect washer to wall connections.

The repair was surprisingly simple. We followed the video and it was a simple fix :)

1)removed philips screws at sides of control panel 2)lifted up and flipped panel over backward 3) disconnected wiring harness to lid switch 4)removed two snap off connectors at top back of washer with screwdriver 5)remove top lid and side housing as one unit 6) removed removed top lid and side housing and core of washer to driveway 7) ran over unit with an Ingersol Rand 84" smooth drum vibrating roller

Popped off the fabric softener dispenser with a medium flat tip screwdriver. Removed the agitator screw with a 7/16 socket. Pulled out the agitator assembly. Pulled out the agitator cam assembly. Removed the 4 worn directional cogs/replaced with new ones. Reassembled in reverse order.

1) Slide retaining ring up 2) Remove old dispenser and toss out 3) Slip new dispenser on and lower retaining ring. Couldn't be simpler. I was surprised that I could actually get an exact replacement. Ordered it and two days later it was at my door. Great service!

Removed the agitator with a straight blade screw driver and then removed by hand the inner cap. Used a 7/16 socket with a long extension and ratchet and removed the agitator bolt. Once the bolt was removed I pulled agitator cam the contains the agitator dogs out of the Mover, Agitator. I replaced the worn agitator dogs with new ones and replaced everything and it worked fine. I did mark with a red Sharpie the direction the dogs were before removing them so I would replace them in the right direction. Very simple job that took less than 15 mins.

Pulled the machine away from the wall about 18 inches. Tip the washer back until resting stably against the wall. Used plies to remove two spring hose clamps. Use the screw driver to remove spring clips. Pulled old pump off and placed new pump on. Replace spring clips and hoses with clamps, and lowered the washer. Done!

the video pretty much told the whole story except I forgot to put the plastic collar piece on the new clutch when I put it back together so I got to do it twice. second time went even easier. Thanks for the video,it was great.