Models
>
11022086102
11022086102 Kenmore Washer - Overview
Sections of the 11022086102
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Lid Seal
PartSelect #: PS11744855
Manufacturer #: WP8054939
This part is the replacement lid seal for your washer. It is made of rubber and is gray in color. It is approximately 21 inches long and 1 inch wide. The washer lid seal creates a seal for your top lo...
No Longer Available
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Single Front Panel Cip
PartSelect #: PS11731288
Manufacturer #: W10854425
This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel...
$16.46
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$11.80
In Stock
Leveling Leg Locking Nut
PartSelect #: PS11741219
Manufacturer #: WP3359452
The leveling leg locking nut is an OEM replacement fastener for use in dryers and washers. It has a head diameter of 3/8 inches and a thread pitch of 16 threads per inch. The nut secures the leveling ...
$7.76
In Stock
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$21.53
In Stock
Screw, 8-18 x 1/2
PartSelect #: PS11741443
Manufacturer #: WP3390631
This screw is sold individually.
$7.84
In Stock
Spray Paint - 12 oz. - White
PartSelect #: PS347819
Manufacturer #: 350930
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Water Inlet Hose Washer
PartSelect #: PS11738697
Manufacturer #: WP16123
If your clothes washer is leaking, it is likely that there could be an issue with one of the hoses. If the hoses are in working order, you should check the washers connecting the hose to your unit. Ru...
$7.95
In Stock
Questions And Answers for 11022086102
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 11022086102
[Viewing 4 of 4]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Parts Used:
-
Michelle from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
64 of 125 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer was displaying FL code, and not draining
1) Pull the washer away from the wall
2) Lean the washer back so it is balanced and you can see the bottom
3) Remove 3 screws along the front edge of bottom plate
4)Remove plate, exposing the pump
5)Remove 2 clips that hold pump to motor
6)Place the deepest pan you can fit under pump
7)Loosen hose clamp, pull ... Read more hose SLOWLY from pump
8)Drain as carefully as possible (its a couple /few gallons)
9)Remove second hose clamp, set pump aside
10)Remove three bolts holding in motor
11)Remove small plastic anchor that goes through frame
12)Follow wires to plastic plug. It is easier to remove the closer to you, then push remaining side of the plug through the mount.
13) Reverse the steps, the new pump motor will go in as one unit because of the torque screws(no clips).
Note: I tried to save the old motor because I could see the clog inside of it. After freeing it up, I re-assembled it ,ran the washer and got the FL code again, So I had to remove it again and replace it with the new one. Now it has been through about
10 loads and is working well.
2) Lean the washer back so it is balanced and you can see the bottom
3) Remove 3 screws along the front edge of bottom plate
4)Remove plate, exposing the pump
5)Remove 2 clips that hold pump to motor
6)Place the deepest pan you can fit under pump
7)Loosen hose clamp, pull ... Read more hose SLOWLY from pump
8)Drain as carefully as possible (its a couple /few gallons)
9)Remove second hose clamp, set pump aside
10)Remove three bolts holding in motor
11)Remove small plastic anchor that goes through frame
12)Follow wires to plastic plug. It is easier to remove the closer to you, then push remaining side of the plug through the mount.
13) Reverse the steps, the new pump motor will go in as one unit because of the torque screws(no clips).
Note: I tried to save the old motor because I could see the clog inside of it. After freeing it up, I re-assembled it ,ran the washer and got the FL code again, So I had to remove it again and replace it with the new one. Now it has been through about
10 loads and is working well.
Read less
Parts Used:
-
chris from davison, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Socket set
19 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken seal
Removed old, pressed on new. This is no story but the reason I am writing is to say how impressed I was with the ease of using your Web site to find my part and of your spectacularly fast service.
Parts Used:
-
Samuel from Grass Valley, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
15 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!