11021292012 Kenmore Washer - Instructions

pull off softener dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble

I used the flat screwdriver to pop off the top of the agitator. then I used my socket wrench with extension to remove the bolt holding the top of the agitator to the bottom agitator. I pulled out the small piece that holds the agitator cogs. The agitator cogs were sheared off. I used my screwdriver to remove what was left of them, cleaned up the unit, then installed the new cogs. Re-insert the piece into the agitator unit and tighten the bolt back. Popped the lid back on top and ran a load of laundry to test. It works perfect! Although the teeth are pretty worn on the agitator as well, so I'm looking to buy a whole new agitator unit next. Very easy fix!!

Exactly as described in the sample video on your site.

Half inch ratchet extension unscrew remove replace cogs reinstall retainer ring drop back in . Watch how fast agitator spins.

I viewed the repair video provided and then dove into the project. I am sorry to say that the time suggested for the fix was a bit misleading. Took me less than five minutes rather than the fifteen minutes suggested. Thanks Parts Select for a great assistance in saving me an expensive repair call!

took broken agitator dogs out and put new parts in, it was very easy repair.

remove top cap on agitator, remove seal from inside of agitator tube( seal looks like garbage disposer stopper)now you see top of bolt head, use 7/16 socket with a 12 inch extension, hold bottom of agitator to keep it from turning while removing bolt,pull up on agitator top to remove, remove assembly that holds the cog's,slide off retainer ring, replace with new cog's, (when reassembling match pins in bottom part of agitator to slots in top part of agitator.)install bolt, install seal(use some laundry detergent so it slides in easily),put cap of agitator back on. that's it

Took the back of the control panel off, lifted the top of the washing machine up took off nuts holding the latch lock off, installed the new parts put back together. Piece of cake...because i got the right parts the first time. Thank you PartSelect.

took top agitator off, cleaned it (needed anyway), replaced agitator directional cogs, replaced washer (old one was too soft to reseal) upon bolting back together. Oddly the repair kit on this website does not include a washer - I only bought the cogs - it turned out to use the same washer I use on my kegerator

Very easy repair less than 15 min. to complete. The ordering was very easy, and quick shipping. Glad to see parts made in the USA.

I had to pry cap off top of agitator. Using a 9/16 socket a 4" extension 3/8" rachet. I loosened the nut holding the top of agitator to the bottom. The reached into the opening and slide the cog holder out. Removed the reainer ring and slide the cogs out. Installation is the reverse. total time less than 15 mins. My agitator is now agitating. Thanks

$3 part and 15 minutes and the problem is fixed.

with socket and rachet with adapter took me like one min. to take off part about one min. to take it apart to get to cogs. and about two mins. to put back together. i say it took 15 to 30 mins. because while parts were off and apart i cleaned them all before putting back together. can't beleive such little parts caused so much trouble. machine runs like new now. thank you

pulled lid off[fabric softner already removed], removed 7/16 bolt, pulled up, removed dogs, replaced with new, reassembled,and WIFE HAPPY!!!

Found a video showing repair steps on YouTube. Removed agitator cap, seal and retaining nut. Replaced old cogs and reassembled.