Models > 11021182010 > Instructions

11021182010 Kenmore Washer - Instructions

All installation instructions for 11021182010 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11021182010
1-15 of 299
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 496 of 503 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.

Washer not agitating

  • Customer: Craig from Polk City FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 468 of 468 people found this instruction helpful
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt that holds the assembly together it is a 7/16 head and because it is in a 4" deep well your will need a 6" extension for your ratchet. Once the bolt is out the top of the agitator, the assembly with the cogs removes by hand. Set the assembly upside down on the counter, slide the black plastic ring off, pull the cogs out with your fingertips, install the new cogs put a new black ring on and set the assembly back in the agitator. Reinstall bolt. As the bolt is down in a tube, you cannot set it in place with your fingers and it will fall out of the socket. To hold the bolt in the socket during positioning you can either put a gob of Vaseline on the bolt head to hold it in the socket or form a small piece of paper over the bolt head and set it into the socket, the friction of the paper will hold the bolt into the socket. Took me less then 10 minutes, good luck

top half of agitator did not move during wash cycle

  • Customer: dennis from new stanton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 176 of 200 people found this instruction helpful
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble

Agitator was not working

  • Customer: Michael from Murray KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 38 of 46 people found this instruction helpful
Step 1) Take off top cap with a flat head screw driver.

2) unscrew bolt (may need extension as it may be deep in the agitator.)

3) Take upper agitator off.

4) remove clog retainer and clogs.

5) insert new clogs and re-assemble.

total time 10 to 15 min.

Lid Lock light blinking, machine will not start

  • Customer: David from Los Alamos NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 28 of 35 people found this instruction helpful
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure

Agitator was damaged from apparent overload

  • Customer: Roy from Salisbury NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 23 of 30 people found this instruction helpful
With the PartSelect website instructions, I was able to take the agitator apart easily, diagnose the problem and select the replacement parts to effect the repair. The only issue I faced was the shipment damage to the repair parts, but the service department with PartSelect responded quickly and fairly to correct the damage. I have never seen a website like PartSelect.com that trains you in making the repairs, provides you with the required parts and then stands by to resolve any issues you face; I was awed by how confident that it made me feel throughout the process.

Upper agitator stopped moving

  • Customer: Craig from Yadkinville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 21 of 25 people found this instruction helpful
First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ears were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.

Screw agitator would free spin

  • Customer: Charles from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 19 of 21 people found this instruction helpful
Job was easy! Just remove the top cap with a screw driver. With a socket and extension, remove the bolt that holds the agitator to the transmission shaft. Pull up on the agitator and lift it off the shaft. I had to use the screw driver to pry off the center piece that held the cogs because it did not what to separate from the rest of the agitator. Removed the pieces of the old, broken cogs, cleaned up the parts and installed the new cogs with the center piece upside down. I then took some silicone lubricant and lubed the area the cogs rub on and the opening the center piece spins in on the rest of the agitator. I then removed the Thrust Spacer on the mail part of the agitator but just lifting off the old one and putting on the new one. Then, with the center piece that holds the cogs upside down I inserted it into the upper corkscrew section of the agitator so that the cogs would not fall out. While holding the two pieces together, I turned it back right-side-up and installed it back onto the other part of the agitator and then on the shaft. Re-installed the bolt and tightened with the socket. That's it! It sounds more complicated then it really was.

Top Half of Agitator would not function without appying sideways pressure

  • Customer: Donald from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 16 of 18 people found this instruction helpful
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remove black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...

Cog stripped causing agitator to not turn

  • Customer: Vicki from Houston TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 14 of 16 people found this instruction helpful
Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined correctly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Top section of agitator not turning

  • Customer: John from Stone Mountain GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 9 of 10 people found this instruction helpful
Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done! Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!

Agitator was barely agitating. Making a clicking noise.

  • Customer: Charmaine from Slidell LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 9 of 10 people found this instruction helpful
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.

top agitator would not operate

  • Customer: Larry from Edgewood TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Agitator moves freely in both directions

  • Customer: James from NAPERVILLE AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 9 of 11 people found this instruction helpful
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
All Instructions for the 11021182010
1-15 of 299