11020996991 Kenmore Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
agitator stop working
-
Floyd from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Water not draining.
Started to replace the water pump but looked online at Youtube and everyone said to look at the lid switch first. I bypassed the switch and sure enough that was it! No need for the pump.
Parts Used:
-
James from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not always spin & was leaking water
Tilted the washer on the side with my wife holding it. Pulled the pump out then replaced it with the new one.
Parts Used:
-
John from Bakersfield, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
agitator was not spinning
well the replacement of the directional cogs was easy, once i was able to separate the the top and bottom half of the actual agitator. What i could not find out about my whirlpool gold was their was 4 plastic tabs that held the whole cog assembly onto the agitator. i could not pull it apart like all the videos were showing, until i took it to a repair shop and he showed me. After i used a hammer with a screwdriver to break the plastic tabs, it popped right apart. The actual repair only took about 30 min. once i was able to get the agitator apart.
Parts Used:
-
andrew from forest, MS
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
broken seal
-
Lorraine from Millsboro, DE
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water Leaking from pump while emptying
Tilt the washer back enough to access the bottom of the washer. Remove two hose clamps with pliers,then remove 2 hoses attached to pump. Remove two metal spring straps and remove pump. reverse to install.
Parts Used:
-
Anthony from Yonkers, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Leaking water pump
Let me start by saying that I only had to wait one day for the new water pump. Awesome! Once I figured out how to accessed the waterpump, the real challenge began. The washer had been leaking for some time and removing the old pump turned out to be more difficult than expected. The bottom clip used to secure the pump was completely rusted. It took some effort to remove the old pump but it finally came off. Once it was removed, I discovered why it was so difficult. The drive shaft from the motor was so rusted that a groove had been worn into it. I ended up using a metal file to smooth off the rust in order to install the new pump. With a bit of coaxing, I was able to install the new pump, re-attach the hoses and re-assemble the machine. It works like a charm now. No more leaking! Yeah!
Parts Used:
-
Linda from Neenah, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Hanger on motor broke and destroyed the coupling
Turned machine on it’s back after removing the hose that goes to the drain, removed the bottom dust guard, I removed the hoses (take a picture before removing things so you know how to orient them when putting it back together) and drained the water first but this is not necessary (there are YouTube videos where they suggest removing the outer case, unclipping the pump and then removing the motor. This would be optimal as you don't need to deal with the water running out of the washer when you remove the hoses). Removed the 4 electrical connectors (multi-plug, 1 x two prong plug and 2 capacitor connector plugs) One of the motor hangers were broken on my machine, I removed the other one and then slipped the motor out. Removed the broken hanger and securing screws and the old rubber grommets, slipped the coupling out (had to leverage out with a large flat screwdriver). Installed new coupling and rubber on the gearbox side, 4 grommets on the motor and the other coupling on the motor. Inserted the hangers on the gearbox side and then mounted the motor. (it is easier if you turn the washer on its back so the drum moves down and gives you more room to drop the motor in from the top), clipped the motor hangers on and fastened the two metal screws, mounted the pump and hoses and reinstalled the dust guard. Turned it right side up and tested before dragging it back into the laundry. Washing again like it did when first bought it in 1998. I would recommend that when a coupling brakes, replace it as well as the hangers and grommets to make sure it has no room for play. Mine broke way too quick as I did the last coupling about a year ago, problem I think was that I had the wrong grommets causing excessive vibration and wear.
Parts Used:
-
Andre from Torrance, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
My washing machine leaked
I followed the instructions on youtube and replaced the drain pump. It was so easy!!! I am so proud of myself and so is my husband! I took off the cover and simply replaced the drain pump. I am such a stud! :)
Parts Used:
-
Rachel from Jordan Valley, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
agitator not turning
all you have to do is watch the video, it does not get any easier then this.
Parts Used:
-
George from Wallace, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Leakt water pump
Forget the instruction book, it's too time consuming and it's a knuckle buster. Disconnect all hoses and lay machine on it's back. (Have plenty of rags to soak up the half gallon of water still in the pump). Use pliers to slide back hose clamps on pump and slide off hoses. Use screw drive to snap off clamps holding pump in place. Remove pump. Simply reverse process to install new pump. It nearly was one of my wife's 5 minute jobs she always has on her "Honey Doo" list.
Parts Used:
-
Carl from Newport, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
direct drive water pump leaking
watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.
Parts Used:
-
gerald from modesto, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer vibrating when in spin cycle.
Replaced suspension, leveling and tub springs.
Parts Used:
-
Calvin from Cheney, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Motor Coupling Broken
I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.
Parts Used:
-
Jeff from Nicholasvile, KY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
agitator would not spin
Took agitator apart as shown in video, changed the agitator dogs, put agitator back together. Works great.
Parts Used:
-
Pat from Breaux bridge, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!