11020972992 Kenmore Washer - Instructions

watching the video was a great help, not a perfect match as mine but enough information to get the job done! parts were cheap & they shipped fast. keep coming with the great videos!

After i pulled the motor off the washer, i found the coupling that was busted,removed it and put on the new one i got from you and just put everything back together again and the machine is operating as good as new again.

watched the repair video on u-tube and followed it. Had trouble separating the top agitator from the bottom agitator after removing it from the washer. I tapped the 4 white tabs on the top with a hammer and screwdriver. Top and bottom separated after that.

I noticed the top wasn't spinning. I took the cap off the agitator and looked inside it. Sure enough the directional clogs were broken. I had no idea what to do. I went online using my phone and discovered partselect.com With their wonderful help I was able to find out what part I needed and order it right from my phone. It only cost me $10 bucks to get it delivered to my house and it shipped in 3 days. I am 21 years old and this was my first washer. Thanks to part select I can keep my washer. Partselect saved me well over $150 dollars plus labor. I will definitely use partselect again!!!

well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

Pulled off old seal. Snapped on new seal. Takes longer to type it than it did to do it.

After 10 years, our washer stopped agitating. While I started looking at new washers on-line, my husband looked at our washer and found that the agitator was slipping because the plastic "teeth" that grab the gear were worn down. I Googled Kenmore washer parts and quickly found Parts Select. We ordered the Agitator Cam Repair kit and were EXTREMELY pleased to see it appear at our door within two days!! In less than 15 minutes, after spending only $32, my husband installed the new parts and, with all honesty, we feel like we have a brand new washer! It hasn't agitated this well in a very long time. Because of this, we saved at least $500 because we didn't need to buy a new washer (which probably wouldn't have been as good as our current one!). Awesome experience--wish everything in life were this easy!!

Video's on parts select are a big help. Just followed the instructions. Only slight problem was the coupling's do not slide easily onto the shafts. I had to use a little lubricant and put a wood block across the opening and tap with a hammer. Maybe a little more than a tap. Also when I was ready to test the repair I found the washer would not stop filling. After much checking I found out on another repair site that the shutoff requires a certain water pressure to work properly. I hadn't opened the faucet fully. Once I did everything worked properly.

Easy, popped cap off top of agitator with edge of knife. Removed bolt from center of agitator,pulled agitator up from shaft. Removed old,worn cogs,replaced with news cogs and reassembled. Tightend with bolt . Replaced cap and bang ,works like new.

So easy it's ridiculous, take the old one off, put the new one on! Can't say I love doing laundry, but I love my new washer lid seal! :)

very easy I followed the Parts Select video that's posted at the site,and covered the replacement very good.Thank You very much.

Removed the actuator cap which gives you access to the screw that holds the clutch dog assembly in place. Once the screw is removed the assembly lifts right out. The clutch dogs have a small retaining band that holde them in place. Once removed the dogs slip right out. Replace the old dogs and reverse the order of the removal process. Very easy.

pull off softener dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble

Turned washer on back, inspected pump area for leak and found crack in pump. Replaced cracked pump with new pump from PartSelect, which arrived promptly. Washer was only down for 3 days and turnup only cost me the price of the part.

Saw your video on how to install a waterpump. It made my life very easy.