Models > 11020927990

11020927990 Kenmore Washer - Overview

Get Parts and Repair Help for 11020927990

If you know the washer repair part you need, you can browse the list of all parts on the 11020927990, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11020927990 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.32

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$11.77

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

$29.84

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$28.77

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

$17.97

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads.

$27.18

Lid Switch Assembly

This part comes with a three-wire lead. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

$3.76

Tub Spring

$8.76

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$3.76

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would not run, lid switch broken

  • Customer: Nicola from Centreville MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 480 of 485 people found this instruction helpful
Repair was easy. Removed two side panels on the control plate. Removed two phillips screws that hold the control panel to the body of the washer. Disconnected the electic connection to the wires leading to the lid switch. Three sided of the lower cover lift over and removed from the washer frame. Access to the lid switch and wire retainers was easy. Re... read more

REPLACE WATER PUMP COUPLING

  • Customer: RICHARD from PHILA PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 476 of 482 people found this instruction helpful
REMOVED CASING TIP OVER WASHER DISCONNECTED WATER PUMP. DISCONNECTED MOTOR THEN REPLACE COUPLING THEN REASSEMBLE MOTOR THEN REPLACED WATER PUMP. read more

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 469 of 473 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more