Models > 11018522791

11018522791 Kenmore Washer - Overview

Get Parts and Repair Help for 11018522791

If you know the washer repair part you need, you can browse the list of all parts on the 11018522791, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11018522791 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.32

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$11.77

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

$29.84

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$30.40

Lid Switch Assembly with Leads

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

$28.77

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").

$17.08

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. I...

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$2.52

Thrust Spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. Th...

$23.22

Agitator Repair Kit

This six piece agitator repair kit comes with a four inch cam, a thrust spacer, and four dogs ears (agitator cogs). This kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover).

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer stopped mid cycle

  • Customer: Travis from Pearland TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 545 of 549 people found this instruction helpful
1. Unplug washer.
2. Remove screws at control panel end caps.
3. Flip control panel back to expose wiring.
4. Detach lid switch wiring harness from control panel.
5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
6. Tilt the front/sides piece over to expose lid switch.
read more

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 486 of 492 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more

The lid switch had broken on my washing machine; the machine would not run.

  • Customer: Dennis from Evans City PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 488 of 508 people found this instruction helpful
First I unplugged the washing machine. Then I removed the two screws that hold the top console in place; these are located in back of the main console (where the dials are). Once removed, the entire console swivels back, exposing the wires underneath. I unplugged the wiring harness that was connected to the washing machine top flat surface. I then remove... read more