Models > 11016942503 > Instructions

11016942503 Kenmore Washer - Instructions

All installation instructions for 11016942503 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016942503
61-75 of 987
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer would not agitate when lid was closed

  • Customer: Timothy from Saint Louis MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
The only tricky part was figuring out how to get to the part. There were only two screws that seemed likely candidates to pop off the control panel (on the back at the corners). Fortunately for me the obvious answer was the right one...the panel lifted up and the new part went in - very easy.

Two problems - washer stopped and had to open and close lid several times to restart. Problem 2 - could not get inlet valve to take in hot water.

  • Customer: Harry from Bensalem PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 7 of 10 people found this instruction helpful
1. Read a repair manual that I bought several years ago for this model. Pictures and notes for removing control panel and back cover of washer were very helpful. Replacing the lid switch was easy as long as you have the lid open when locking it down. The control valve was easy and I swapped out wires one at a time to make sure I didn't swap hot for cold. I then removed valve and locked down new one. Reversing the control panel and back skin were easy with a second set of hands to hold the back panel in place while installing two bottom screws. The parts resolved the problems.

Top section of agitator would not spin.

  • Customer: Russell from Hyannis MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 7 people found this instruction helpful
Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

Washer basket off-center and wobbling during spin cycle

  • Customer: Craig from Woodland Hills UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

Leaking discharge hose

  • Customer: wayne from webster KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
removed old hose clamps and hose using pliers. Installed new hose which had all new clamps preinstalled on new hose.

tub oscillation

  • Customer: leonard from phil campbell AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 7 of 12 people found this instruction helpful
placed washer on side and installed new pads
and returned washer upright

No cold water entering machine

  • Customer: Steve from Bethel ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
After uplugging and removing the hoses from the back of the washer, 1 - Removed four screws that secure control panel to top of machine and tilted panel toward front. Disconnected wiring plugs as req'd to gain more access. 2 - Removed the two gold colored clips that secure the top to the lower sheetmetal housing and tilted the lower housing away from the back of the machine. 3 - Removed the shield that is clipped to the back just above the inlet valve assy. 4 - Removed the hose clamp from the valve, disconnected the four wires to the valve (note their position), Removed the single screw that secures the valve assy to the back and removed the valve assy. Installation is reverse of above.

Washer would not work in agitate or spin cycle

  • Customer: yesenia from apopka FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.

Washer tub off balance and noisy

  • Customer: Gregory from Kent OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 4 of 4 people found this instruction helpful
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.

Water Pump was leaking

  • Customer: Rick from Liberty SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

Tub did not center and seal was hanging out of tub

  • Customer: James from Nelsonville OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 5 of 8 people found this instruction helpful
Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension) then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM

Washer would not wash,spin or drain.

  • Customer: Michael from Covington LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
I thought that the lid switch was the problem why the washer would not perform the drain or spin cycle. I broke the lid switch by moving the wires around. I rigged it so my daughter could use it by screwing a screw in the switch til the new one came in. After a few days, the machine stopped working again as stated above with the motor. I purchased a new Whir-pool washer for her and later found a white wire that connects to the electric motor was burnt around the connector in that only one tiny wire was still attached. I reconnected the wire in the connector and the washer started working again.

washer would fill but not run

  • Customer: steve from madison SD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 11 people found this instruction helpful
After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.

the washing machine would pump the water out, but the agitator would not spin, and it was making noise.

  • Customer: mario from eastchester NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

washing machine will agitate but not spin

  • Customer: Robert from Manchester CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 10 of 23 people found this instruction helpful
I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.
All Instructions for the 11016942503
61-75 of 987