Models > 11016942500 > Instructions

11016942500 Kenmore Washer - Instructions

All installation instructions for 11016942500 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016942500
946-960 of 1,001
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no spin dry

  • Customer: Walter from West Palm Beach, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
... exactly as shown in the video in addition to shutting water, removing hot & cold lines & waste tube. I was amazed at how fast the parts were delivered in two days regular shipping. Machine now purring a wifey happy once again! Thanks for the great service & video! I recommend PartSelect highly! WSD

Bad Motor Coupler

  • Customer: Hilary from Gainesville, FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
So, the instructional video was great but be warned that you REALLY need to hammer the part into place. Basically hammer it into place so that the end of the shaft that it goes on is flush with the plastic piece of the coupler on both ends. Otherwise, you'll put the washer together and run a load and it'll squeal and smell like burning rubber. We had to take it apart like 3 times before we got it on there securely enough. We would then run an empty load and it would be fine but as soon as we would add clothes the squealing and burning would ensure. So, my advice is to hammer it in well and save yourself the time and struggle!

direct drive motor coupling

  • Customer: Eugene from Chiefland, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

Tub will not spin

  • Customer: Rick from Terre Haute, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.

Motor Coupling Broken

  • Customer: Jeff from Nicholasvile, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.

The washing machine started making a clicking type noise and would not drain after the rinse cycle completed.

  • Customer: Larry from Buffalo, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.

Washer full of water not draining

  • Customer: James from Port St Lucie, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

No drive from motor

  • Customer: eugene from sussex, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and it was very straight forward, very easy and time saving. I just wish the delivery time for the part was that fast (It was a quick delivery).

Motor Coupling failed after 20 years!

  • Customer: Brian from Spring Hill, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Determined based on some Internet searches that the part that we needed was the motor coupling; washer would not spin or agitate. Once I figured out how to removed the cover (by the way, one of the guys at an appliance store told me how to do it), and reviewing the video on your website, I removed the two screws and four clips, dropped the motor, inserted the parts and put it back together - all in about 15 or 20 minutes. It was easy and clean and the washer worked again. Hopefully go for another 5-10 years. Thanks.

Washer made a spinning/grinding noise when it tried to agitate or spin.

  • Customer: Charleen from Aiken, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video that PartSelect provided on their web site. The instructions were very precise and easy to follow. I watched the video twice and just followed the instructions. I would highly recommend this approach to washing machine repairs. It certainly saved me a lot of money.

The washer stopped agitating but the motor can be heard running.

  • Customer: Albert from Bellflower, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video installation instruction was clear and very easy to follow. However, after installing the parts and started testing the washer, the water overflowed. It looks like the water level sensor wasn't working. It caused a little flooding in the area where the washer is. I took the control panel apart once more and this time diagnosed the water level sensor and analyzed how it works. After spending almost 45 minutes with, I detached the hose attachment and blew air which caused air bubbles in the inner side of the drum. I bent the hose to hold the air while re-attaching same to the sensor. This fixed the problem and the washer is once more, operating normally. Please include this part to your video instruction. Overall, it took me 8 hours on the project including the cleanup due to overflow.

Not spinning and noise

  • Customer: Dean from Belleville, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
First of all I must say thanks guys for your help, the instructions were right on the money. I first replaced the clutch as per the instructions but found out that the problem was the motor coupling ........ It was broken. I ordered it, followed the instructions and I was a hero in my household. Once more thanks guys.

would not wash or spin out

  • Customer: Scott from Coraopolis, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
took off front cabinet removed pump,and then motor and replaced part.

Washer was not spinning, but making a loud spinning noise.

  • Customer: William from Sonoma, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Disconnected power. Disconnected hot and cold, and drain hoses and placed in a plastic bucket. Pulled cover off the washer. Tilted washer onto its back. Removed 2 clips holding the pump. Disconnected wire harness from motor and removed 2 clips holding motor starting with lower clip. Removed a screw from the upper clip used for shipping. Set motor aside and removed broken pieces of the motor coupler from motor and transmission. The replacement part had a metal sleeve in the center of each white plastic ring. The old part did not. This required tapping the new ring onto both the motor and transmission shafts with a socket and makes for a tight fit. Reversed the process to put everything back together. Some alignment might be necessary to place motor to transmission. I recomment wearing thin work gloves to avoid nicks from sharp edges. I didn't. Washer is spinning again and sounds a lot better.

The washing machine basket wouldn't spin

  • Customer: Kali from Missoula, MT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Remove the cover of the washer, pull out motor, pry out motor coupler, replace. May have to hammer with a rubber mallet to get it on. Replace motor and washer cover. We also replace the water pump. It wasn't broken, but since we had the washer torn apart, decided to replace it as well. There are lots of YouTube videos to help you out.
All Instructions for the 11016942500
946-960 of 1,001