Models > 11016922502 > Instructions

11016922502 Kenmore Washer - Instructions

All installation instructions for 11016922502 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016922502
946-960 of 992
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bad Motor Coupler

  • Customer: Hilary from Gainesville, FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
So, the instructional video was great but be warned that you REALLY need to hammer the part into place. Basically hammer it into place so that the end of the shaft that it goes on is flush with the plastic piece of the coupler on both ends. Otherwise, you'll put the washer together and run a load and it'll squeal and smell like burning rubber. We had to take it apart like 3 times before we got it on there securely enough. We would then run an empty load and it would be fine but as soon as we would add clothes the squealing and burning would ensure. So, my advice is to hammer it in well and save yourself the time and struggle!

direct drive motor coupling

  • Customer: Eugene from Chiefland, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

Motor Coupling Broken

  • Customer: Jeff from Nicholasvile, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.

Motor Drive Coupling

  • Customer: Kenneth from Stoughton, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and that was a great help. I just entered my model number and selected the symptom. 61% of the time the drive coupling is the problem and it was. Ordered the part and got it the next day.

The washing machine started making a clicking type noise and would not drain after the rinse cycle completed.

  • Customer: Larry from Buffalo, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.

Washer full of water not draining

  • Customer: James from Port St Lucie, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

Washer was not spinning, but making a loud spinning noise.

  • Customer: William from Sonoma, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Disconnected power. Disconnected hot and cold, and drain hoses and placed in a plastic bucket. Pulled cover off the washer. Tilted washer onto its back. Removed 2 clips holding the pump. Disconnected wire harness from motor and removed 2 clips holding motor starting with lower clip. Removed a screw from the upper clip used for shipping. Set motor aside and removed broken pieces of the motor coupler from motor and transmission. The replacement part had a metal sleeve in the center of each white plastic ring. The old part did not. This required tapping the new ring onto both the motor and transmission shafts with a socket and makes for a tight fit. Reversed the process to put everything back together. Some alignment might be necessary to place motor to transmission. I recomment wearing thin work gloves to avoid nicks from sharp edges. I didn't. Washer is spinning again and sounds a lot better.

Washer would not always spin

  • Customer: Donald from Metter, GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I purchased the part from PartSelect because it was very reasonable and it was OEM part. I have never replaced this kind of part on a washer so I figured it would take me a while. But PartSelect supplied a video showing the entire repair and that was the only reason I did not struggle with the repair. I will definitely buy any appliance parts I need in the future from PartSelect. Thanks Don

Would not spin,but would fill and drain and could hear motor and trans worked

  • Customer: Diana from Sherborn, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow instructions in part repair video from part select,but put washer on back first to see if can access area without removing the whole outer cover we did not even need to do that step only took 20 minutes to replace coupling. The video was great

Washer wouldn't spin and we could see coupling was broken

  • Customer: Sharon from Marina, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We watched the how to video...repair took less than 15 minutes. You can't go wrong if you just watch the easy to follow video! Washer works as good as new.

motor running . no spin cycle

  • Customer: joe from loveland, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Tipped the washer on its side and took the pump off then the motor then the coupling.

bushing between motor and transmision broke

  • Customer: NAN from mt carroll, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched the video on line showed how to do it took about 45 min no problem

washer would not spin or agitate.

  • Customer: Gerald from White Cloud, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
electric unplugged, removed water lines. two screws on back of control housing removed, tilted housing back, removed two clips on top of washer housing, removed body. tilted washer backward, removed brackets on water pump and electric motor, pulled motor off and removed broken parts on shaft, replaced with new parts. Lining up motor shaft to washer was a bit tricky but time and patience got it togather. replaced brackets on motor and water pump. put washer upright and put body back on the body has to be set on guides correctly or will not set right. replace clips andtilt top down and screw it. hook up water lines, and electric.

The washer was making noise and was leaving the cloth dripping wet at end.

  • Customer: Kenia from Orlando, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Before I even watch any partselect videos to do the repair, which I should of from the very beginning, ah, ja, ja, I had already disassembled the back panel "my way" to the washer and trouble shooting the washer with my wife's help. While she tilted the washer backwards, I looked under and we found that the noise was coming from in between top of the motor where the direct drive motor coupling is located and the clutch assembly came together which I learned along with names and functions after watching the partselect installation video. Nice! Once I received the part it took me like 45 minutes to put all back together. Took loose two screws to clips holding the motor, pulled motor of mounting bracket finding the broken piece, replaced it, recouped reinstalling motor onto the motor bracket, clip, clip the two little screws and walla, got the wife her washer back, at bed time rewards, peace of mind the rest was history... Thanks PartSelect for awesome videos and great customer service!

agitator,drive motor coupling,water pump 3 problems

  • Customer: judy from lawrenceville, GA
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch the you tube, and try to fix it by myself,to save money, and moving trouble.this is my first time fix a big machine like this,I was a little scare, but after I saw the youtube about how to fix the washmachine,I start to give a try.it take little bit more time for me to figure out ,but I finally made it. now I can wash my cloth now, and perhaps fix washmachine for my exrat income.( message sharing from an asian 58 yrs old lady, sorry for unable to show step by step due to English not very good)
All Instructions for the 11016922502
946-960 of 992