11016882500 Kenmore Washer - Instructions

Have replaced the rubber "dogs" in the agitator before. Washer had an extended service contract that expired in 1986. It just won't die.

Replaced them as I saw it done in the video. It made it a piece of cake!

removed the two screws from the back of the dial bar on the top of the washer. removed original unit, and install the new unit.

I was expecting to spend $100 or more if not having to go buy a new washer. I found your site and I was like "wow" then I found the Video of the intsual. It could not be any more simple. Entire job took 5 min. And under $4 for parts. All I can say is outstanding and thank you

DIAGNOSIS 1) Popped off the agitator cap. 2) Used a 1/2" socket extension driver to back out the plastic retention nut 3) removed the agitator and poured all the little plastic pieces into my hand 4) googled up the agitator assembly by model number, led me to Part select website 5) identified the plastic pieces as "dog ears" 6) ordered new dog ears for just under $4 REPAIR 1) waited 3 days and got dog ears in the mail 2) had a beer and opened the mail 3) inserted the dog ears into agitator assembly according to the picture on Part Select web site 4) had another beer 5) installed the agitator back into the washer, tightened the retention nut 5) admired my handiwork with another beer 6) washed a load of clothes DIAGNOSIS TIME - about 15 minutes REPAIR TIME - about 4 minutes plus 10 more to drink the beers

I gave the parts to my wife. Then I took them back and fixed the washer .

The repair went very quick and easy. What made this repair so quick and easy is because of the very prompt and quick shipping of the replacement part from this company. This was my first experience with this company and will always use in the future. I ordered the part one day and the very next day I received the part. Great job to this company!!!!!

used socket wrench with an 8in extension to remove agitayor bolt that was under cap on top part of agitator. was back together in about 15 min.correct parts were shipped in record time.

Removed and took apart agitator and replaced directional cogs.

It was my Mothers washer & did find out the Direct drive Motor Coupling was a little warn & replaced not to hard but took more time to get top off because you have to really get under the top off hood & clips where really in there the vidio showed held on with screws & on this Kenmoore Elite the Clips are under the Hood which does make it alittle bit harder so you have to be careful not to bend up the Hood where all your controls are , But did not solve the issue. Looked at lid switch & it was damaged so now going to Replace it. If this was my machine probably would be a bit easier to have seen it is the Lid switch hopefully this next part will fix the problem.

I noticed a leak on the floor. I check the hoses for tightness on the back of the washer and the hoses going to the facets and drain. After disconnecting the hoses going to the washer, facet and drain, I then flip the washer on it's back and examined the underside for wetness. All the underside hoses appeared to be not leaking. I then disconnected the two hoses going to the pump with channel-locks, and I disconnect the two clips holding the pump with just my hand and removed the water pump. I then poured water into the hoses' opening on the water pump itself, and I discovered a slow leak occurring from the shaft area on the water pump. I searched PartSelect and luckily found a water pump that matched. I then installed the new water pump (after receiving it a few days later) in reversed procedures of disconnecting the old water pump. I tested the washer by adding a little bit of water into the washer then switch the dial to spin cycle in order to empty the water inside the washer--no leaks occurred and I was extremely happy.

Because your video was done so well, it only took about 10 minutes to make the replacement. I was really impressed when my tracking notice was e-mailed it included the link to the instructional video. I will recomend your web site to others.

I was skeptical that this would take less than 15 minutes, but it actually took closer to 5 minutes! (1) Remove the fabric softener cup from the top of the auger by pulling up on the collar as indicated. (2) Pry the cap off the auger with a small screwdriver. (3) Use a long 1/2 inch socket extender (with no socket on it) to unscrew the plastic retainer for the mechanism at the top of the auger. Remove the mechanism. (4) In the mechanism, there's a thin collar holding in the agitator directional cogs. Pry that collar up to remove it. This was the trickiest part. I was afraid of breaking that collar but it survived. (5) Replace the cogs. (6) Reverse the previous steps.

Since I live in a condo (upstairs unit) flipping the machine was not an easy option. So I was faced with having to get the remaining 2-3 gallons of water out of the drum. I rigged something up and collected 80% of the water, but be prepared for a mess. I was and it wasn't a big deal, just took more time. Once part was removed, I got online to find the part- which ranged in price from $67 at a local appliance part distributor to $49 from SearsDirect including postage. Parts select came in at $37 with freight and the part swapped out perfectly- just 2 clips that hold the pump on and 2 hose clamps (I used slip-joint pliers which works well). I checked YouTube for a video first and lo and behold, there was a video about a whirlpool water pump replacement, which helped some. Job went well and I didn't have to replace a $1200 all-in-one.

It was easy with the video.I watched trouble shooting videos till i found the problem. wrote dwn the tools needed.watched video[lucky for me i would have forgot a step without it]orderd part, and was the hero