Models > 11016852503 > Instructions

11016852503 Kenmore Washer - Instructions

All installation instructions for 11016852503 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016852503
61-75 of 1,074
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

top agitator would not operate

  • Customer: Larry from Edgewood TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

WILL NOT SPIN

  • Customer: Daniel from Temple TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 8 of 9 people found this instruction helpful
THIS IS A RELATIVELY NEW WASHER AND FAILED EARLY. MY PREVIOUS WHIRLPOOL WASHER LASTED 20 YEARS WITHOUT ANY REPAIRS.
1. FIRST INQUIRED ABOUT THE SPIN PROBLEM IN PARTSELECT. MACHINE WILL NOT SPING UNLESS MANUALY FORCED THEN IT WILL TAKE OFF BUT WEAK.
2.PARTSELECT SUGGESTED A CLUTCH PROBLEM. ORDERED THE PART THAT CAME FAST. WHEN I TRIED REMOVING THE SHAFT HUB WITH A HAMMER AND CHISEL IT WILL NOT GET LOOSE SO I OPTED ORDERING THE SPECIAL WRENCH TO LOOSEN THE TUB HUB.
3.I PUT THE MACHINE ON ITS BACK AND LOOSENED THE PUMP RETAINING CLIPS. DO NOT REMOVE THE HOSES FROM THE PUMP. MOVE THE PUMP AWAY FROM THE MOTOR SHAFT. REMOVE THE MOTOR ELECTRICAL CONNECTOR AND SET ASIDE.
4.REMOVE THE THREE BOLTS HOLDING THE GEARBOX-MOTOR ASSEMPLY AND PULL IT OUT OF THE TUB.
5.PUT THE ASSEMBLY ON A TOWELWITH SHAFT UP AND REMOVE THE SEPARATOR WASHER FROM THE OLD CLUTCH THAT IS SITTING ON THE GEARBOX. THEN REMOVE THE C-RETAINING CLIP FROM THE SHAFT.
6.PRY OUT THE WIRE RETAINING CLIP FROM THE CLUTCH AND PULL THE OLD CLUTCH OUT OF THE SHAFT.
7.THE CLUTCH KIT I ORDERED CAME WITH A PLASTIC BRAKE TO CLUTCH CAM SO I REPLACED IT TOO, JUST REMOVE THE RETAINIG CLIP FROM THE BRAKE THAT IS AT THE BOTTOM OF THE TUB AND REPLACED THE PART.
8.INSTALLED THE NEW CLUTCH AND THE RETAINING CLIPS IN REVERSE ORDER. REPLACE ALL PARTS THAT CAME WITH THE KIT. THE NEW CLUTCH SPRING WAS ALREADY IN PLACE.
9.PUT THE ASSEMBLY BACK INTO THE TUB AND RE-INSTALL ALL THE OTHER ITEMS IN THE SAME ORDER. IT SPINS GOOD NOW!
10.WHILE REPLACING PARTS, METHODICALLY CLEAN ALL THE LINT FROM THE MOTOR AND FROM UNDER THE MACHINE. THE GEARBOX SHOWED SIGNS OF LEAKING OIL SO ITS A QUESTION OF COST. I LEFT IT THERE UNTIL IT FAILS THEN I'LL BUY A NEW MACHINE.

The support sprint had broke which left the basin unleveled so water would leak behind the basin and onto the floor

  • Customer: Michael from Newark DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 30 people found this instruction helpful
I replaced the broken support spring and the problem was fixed

Hot water would not stop running into machine when machine is off.

  • Customer: Jon from Lafayette IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 12 people found this instruction helpful
Unplug machine then removed two screws from the back of the control panel so that the panel could be removed from the top of enclosure. I then removed the two spring clips that fastens the enclosure to the back panel of machine. Stand in front of machine and tilt enclosure back towards you, this opens up the machine to get access to the inlet valve. Remove all electrical wires and the water hose at the bottom of the valve. There was only one bolt that attached the valve to the back panel; remove it and replace water inlet valve.

Washer would'nt spin

  • Customer: Dean from Poplar Grove IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 7 people found this instruction helpful
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

Washer would not spin a full load.

  • Customer: Ralph from Newbury Park CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.

spin cycle was not working / poor

  • Customer: Craig from Plano TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 8 of 10 people found this instruction helpful
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

Spin cycle not working properly; Clothes still soaked when spin cycle finished

  • Customer: Sarah from Columbus OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing completely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.

stopped working only filled with water.

  • Customer: Christa J from ElDorado Springs MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
Fast simple and supper easy! Please do not waist your time or money on repairmen that rip you off. You are garunteed all the way or your money back from Parts Select. Go to your model number than read a few stories of others to better pin point your problem then order part and your item will ship fast I had my part on the 2nd day of the order. Do not be fooled you can do it easily! I have order twice and both items went smoothly and took less then 10 minutes to put in. Thanks Parts Select for making it possible for the little guys and supporting them and not the big rip off scammers. I will be back when needed. May you continue in your good deed! C.S.

Water Pump was leaking

  • Customer: Rick from Liberty SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

washer wouldn't start up after filling & closing lid

  • Customer: Jeremy from Marengo IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 11 people found this instruction helpful
First I loosened the 2 screws on the outside of the top control assembly with a philips screwdriver. Then I took out the 2 other screws toward the top on the back with a socketwrench.Next I removed the top so I could access the switch. After that I removed the broken switch and unhooked from wire hareness. I then hooked up the new switch and snapped into place. Last I put the top back on and screwed into place.

Replaced ring that broke and washer that was bent on the edge.

  • Customer: Kim from West Liberty OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 16 of 35 people found this instruction helpful
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

No agitation, No spin, pump OK

  • Customer: Ernest from Midlothian VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 6 people found this instruction helpful
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.

  • Customer: Kevin from Disputanta VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 9 of 15 people found this instruction helpful
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

Machine agitated during cycle but would not spin clothes dry.

  • Customer: Kurt from Bremerton WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.
All Instructions for the 11016852503
61-75 of 1,074