Models > 11016812501 > Instructions

11016812501 Kenmore Washer - Instructions

All installation instructions for 11016812501 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016812501
1,261-1,275 of 1,313
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

would not agitate

  • Customer: art from denver CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
searched the internet for the problem, saw video on you tube, bought the part & repaired/replaced the couplers. You have to make sure the couplers are all the way on the shafts, so the washer can be reassembled correctly. After it was reassembled, the machine would not go through the cycles. Apparently unrelated, the lid switch had become defective. I ordered the part & fixed the problem. That repair is also on you tube.

washer did not work after replacing agitatior parts

  • Customer: kimberly from Grass Valley CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I was thrilled that the agitator parts were so easy to replace, but that didn't totally fix my problem. I looked underneath the washer and found black rubber shavings from a worn part and looked online and found that the problem was most likely the Direct Drive Motor Coupling. I watched the video and ordered the part. The coupling was actually broken. After replacing the part, the washer works great...better than it has in years. I think I will work on our dryer now.

Drum not spinning!

  • Customer: Lew from Saint Simons Island GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the on site video.....Did everything except removing the cabinet....Laid the washer on the front side and did the repair underneath in less than 30 minutes.....I might add the new coupler is much better than the original which was all white plastic....The new part was nylon and had metal inserts. The original had no inserts. Some have said the original part that had the two flat sides would just round out causing the drum not to agitate or spin. Mine just broke in half. I don't see this new part breaking or rounding out the metal inserts.....I might add Whirlpool OEM part was costing much more and with a 5 business day wait on delivery....Parts Select 1.8 day was advertised and it came in two days.....You won't go wrong doing business with Part Select.

Two out of six interlocking spokes of the plastic flex-coupling hubs had broken off due to years of service. Contributing factors were running heavy bath towels.

  • Customer: Will from Arroyo Grande CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Was going to "...just take it apart and fix it" as my career covered being a mechanic, machinist and vocational instructor for over 35 years. Just in case. I decided to visit the PARTSELECT" website for "How-To" guidance. There I fund excellent troubleshooting guidance, including root-cause analysis in % of likeliest cause(s). This was followed with a brief step-by-step descriptions of "How-To" activities, including necessary tools. Best of all was the short instructional video, showing exactly how to go about the repair in a safe and systematic manner. As a former instructor, I am truly impressed by the quality of the material and service this website offers! It made my job so much easier, and consequently it was well done in no time. I urge every customer to follow the excellent guidelines and strongly recommends this site to others. Total cost of my repair was $11.00 for the part, plus shipping; saving me a bundle and possible grief and frustration! The website gives great customer service off- and on-line with follow through by courteous personnel. Thank you for the superior customer service and level of support at every step!

Lost the spin cycle and had a rumbling noise.

  • Customer: Brent W from Amelia OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I performed the repair the same as outlined in the video, but I didn't need to tip the washer on the back side. Once I removed the sheetmetal, I was able to swap out the drive coupler, and the new part is a better design than the one that broke.

Drum wasn't spinning during spin cycle.

  • Customer: Douglas from Blue Point NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the directions in the two videos that were provided on your web sight. It fixed the problem and it only cost us about $60.00. We were so thrilled with the results. We were almost ready to go buy a new washer. My wife suggested that we look it up on line and see if we couldn't fix it ourselves before spending the money on a new washer. Was she ever right! Thanks for providing such fine instructional videos.

washer not spining

  • Customer: Israel from san antonio TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
took motor of 2 screws instaled motor coupling

Machine fills then just hums

  • Customer: Kevin from Center Point TX
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After alot of helpful advise from you guys I replaced coupling water pump clutch, and the problem was still their. Then I tested motor capacitor and it appears dead. So I should receive new one tomorrow and hopefully success! I turned machine over and oil leak..so that's where the string with hose and air needle come in handy to put 90weight oil in through breather hole in gear case.

will not spin

  • Customer: Fred from Centerburg OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
one thing that you do not need to do is to remove the pump from the motor, I tried to remove it as per the instructions but the pump cracked,remove both inlet and outlet hoses from the pump and remove the pump and motor together, don't try to take them apart, you don't need to, thanks

Washing Machine stopped spinning and agitating, clicking/hum noise when lid closed.

  • Customer: DAVID from BATH PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Did not know problem or how to access - thought the back came off washer. Typed in symptoms and it pretty much pinpointed the most likely cause. Watched video on how to take it apart (BTW the front and sides come off, NOT the back). Followed the guide, took motor off and sure enough one of the plastic couplers was cracked. Ordered from PartSelect and with regular shipping the cost was under $20 (ordered Tues. night, had it by Thurs.) Installed part - note as someone else said the new piece has metal inserts which make it really snug to go around the drive shaft, but the tip about using an oversized socket and some light taps to get it on worked liked a charm. Put it all back together (getting case back on was toughest part)and its been working fine for the last week - heavy & lite loads. Have to say was thinking the whole thing needed to be replaced (sound & age) but for $20 it was worth the shot...Glad i came here first!

no spin cycle at all still pumps

  • Customer: rex from yorba linda CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed website instructions, worked for a couple days, appears it needs clutch or possibly transmission(red oil present)

washer would not agitate or spin, even after replacing coupler

  • Customer: GEORGE from GERMANTOWN KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Found input to gearcase deformed, so new coupler slipped under load. Replaced gearbox. All function restored, but machine banged harshly during spin. Discovered that "skid plate" had shifted during gearbox replacement. Remounted skid plate carefully with pry bar, correcting vibration.

No spin cycle

  • Customer: Stephanie from Frederick MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I pulled up PartSelect, compared their advice with my problem, ordered a direct drive motor coupling for my particular model, received the delivery, and called a friend who's good at home repairs and who happens to be dating my sister. He was delighted to comply with our request (her clothes get laundered here) and he had no problem with either the repair itself or the part we ordered. Replaced the hoses, too. He said the new part had been improved over the old one, but everything fit together just like it should. Then I washed her work jeans. Success! I know this isn't what you're asking, but I was so pleased to have the correct part ready to go so he didn't have to mess around. It wouldn't have taken the afternoon, but I had to clean everything that had accumulated debris in 10 years of use as he went.

direct drive motor coupling was broken

  • Customer: Abdel from Roswell NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Friend of mine did it well

agitator wouldnt move

  • Customer: robert from Roanoke VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Well i'm an auto technician by trade so I just jumped right in without reading or watching anything, but I saw the video and in the days waiting for the part to show up I watched it. I would recommend everyone to watch the video because it is simpler than I made it.Easy repair any mechanical skills at all and you shouldnt ave any trouble.
All Instructions for the 11016812501
1,261-1,275 of 1,313