Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11016732500 > Instructions

11016732500 Kenmore Washer - Instructions

All installation instructions for 11016732500 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016732500
1,006-1,020 of 1,094
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer vibrating when in spin cycle.

  • Customer: Calvin from Cheney, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced suspension, leveling and tub springs.

Motor Coupling Broken

  • Customer: Jeff from Nicholasvile, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.

agitator would not spin

  • Customer: Pat from Breaux bridge, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Took agitator apart as shown in video, changed the agitator dogs, put agitator back together. Works great.

Clothes soaking wet after wash cycle completed

  • Customer: Justin from O'Fallon, IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the helpful video from PartSelect. Removal and Replacement of the Clutch Assembly was fairly easy. Just make sure you have enough towels to dry up any water that may come out after tipping the washing machine over. After Replacement the washing machine works like new. Thanks PartSelect.

Machine had been walking and vibrating for a couple of months during the spin cycles.

  • Customer: Roland from Navarre, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Looked on line and found the cheapest repair for my symptoms seemed to be the tub wear pads. Disconnected the washer, tilted it to where I could inspect the pads and discovered one was missing. So ordered a set, (Only complaint was the shipping was as much as the part). Parts arrived in 2 Days (!). Tilted the washing machine again...reached up with a small flathead screw driver and pryed the old pads off...snapped the new ones on (takes a little pressure, so eat your wheeties)...and job done. Stood everything back up and re-connected hoses, drain and plug...Works like brand new...Unfortunately for the wife who thought she was going to get a new one....LOL

The washing machine started making a clicking type noise and would not drain after the rinse cycle completed.

  • Customer: Larry from Buffalo, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.

Would not spin out all the water from clothes

  • Customer: Michael from Tallahassee, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Similar to the youtube repair video, followed it mostly. This model has a different plug in set up on top where the wiring is. Just unplugged a different plug in a different location. The other difference is that I did a lot of dusting and vacuuming of inside parts and around motor. Also used some spray on rust converter on some rust spots then coated those areas with spray paint. Also where wire harness hooks to the frame I taped up a longer section of the wire to keep the wires together so they could move around and not be damaged. The actual repair took about a half hour, but took more time taking the washer outside on porch then back into the house. Out side repair is better because a significant amount of water came out of the washer and drain hose when we tilted it on the back to remove motor and transmission. Just follow the youtube video instructions and most people should have little or no problems doing the job.

Washer full of water not draining

  • Customer: James from Port St Lucie, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

Agitator didn't spin but everything else worked.

  • Customer: Kenneth from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
The youtube explanation on how to repair was great, especially the instruction to lift up on the bluish plastic ring (to detach the softener dispenser), and not to tighten the bolt too much when reassembling matters.

top half of the 2-part agitator slipping (not turning) due to stripped teeth on these cogs.

  • Customer: Alan G. from Groves, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
removed the softener dispenser, gently pried off the top with screw driver, loosen nut and lift off the unit holding the cogs. On our (Kenmore, series 90) there was a small retaining ring to hold the cogs in place. Removed retaining ring (no tools), and cogs (one at a time). Replace each old cog with the new one, being careful that it's not upside down or backwards. reassemble. test. rejoice! This $3 part plus $7 S&H - saved a $100 house call from the appliance repair man.. YouTube & PartSelect = super Combo! Thanks!

The tub would not spin during the spin cycle. I diagnosed that the door switch was functioning. And through some reading on the internet, found out it was the motor coupling. I replaced the clutch assembly strictly as preventative maintenance.

  • Customer: Jorma from Saint Cloud, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

Chlothes were coming out wet at the end of the cycle.

  • Customer: James from Bel Air, MD
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Parts select gives you the top solutions for the problem you are having. This suggested a clutch, and upon looking at mine I could see it was displaced. I watched the instructional video, and it was spot on. It told me how to from beginning to end and it worked out perfectly. I spent about an hour of my time, spent $38, and my machine is fixed. Thank you Parts select for the free video, I couldn't have done it without it.

Replace leaking water pump

  • Customer: Dewey from DeRuyter, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair video was very helpful and exactly right. The most difficult task was removing the old pump. It had apparently seeping between the motor shaft and the pump coupler for some time and had rusted the pump to the motor shaft. I had to aggressively grip the pump housing with the channel lock pliers and wrench it back and forth to break it loose. I took a file to remove the rust build up from the motor shaft before installing the new pump. Washer works fine.

Washing machine shook violently during spin cycle

  • Customer: brian from las vegas, NV
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Luckily enough the washer shown in the demonstration is my exact model, which eliminated any variables I may have come across. The repair was relatively easy and probably could of been done in less time but I took every step slowly to avoid breaking something or leaving something unattached. For the money and time spent on this repair I would certainly recommend this for anyone with a similar issue. After taking the machine completely apart, i found that the suspension pads were still properly functioning. Since i had already purchased them with the tub wear pads, I changed them anyway. The trickiest part for me was pulling the outer tub out because the shaft on my unit was very rusted had a considerable amount of buildup on it. During this step I was very careful to remove all the build up because there is a single rubber seal between the center opening of the tub and the motor shaft. After I made sure the shaft was completely smooth and there were no protrusions I gently rocked the tub back and forth while applying pressure from the underside of the tub, all the while making sure that the seal didn't fold in on itself or stretch in any direction. Other than that, the repair went very quickly and easily . The spanner wrench is a must !!! I actually found it on amazon for about 6 dollars and I'm positive I will find another use for it somewhere down the road. I owe a big thank you to Steve. (the guy in the video) and everyone else from parts select for making laundry day in my house tolerable again !!!

Had issues with removing the inner tub

  • Customer: Bruce from Yankton, SD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
All Instructions for the 11016732500
1,006-1,020 of 1,094