Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11016732500 > Instructions

11016732500 Kenmore Washer - Instructions

All installation instructions for 11016732500 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016732500
76-90 of 1,094
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Spin cycle not working properly; Clothes still soaked when spin cycle finished

  • Customer: Sarah from Columbus, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 10 of 13 people found this instruction helpful
We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing completely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.

Will Not Spin

  • Customer: Daniel from Temple, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 9 of 11 people found this instruction helpful
This is a relatively new washer and failed early. My previous whirlpool washer lasted 20 years without any repairs. 1. First inquired about the spin problem in partselect. Machine will not sping unless manualy forced then it will take off but weak. 2. Partselect suggested a clutch problem. Ordered the part that came fast. When I tried removing the shaft hub with a hammer and chisel it will not get loose so I opted ordering the special wrench to loosen the tub hub. 3. I put the machine on its back and loosened the pump retaining clips. Do not remove the hoses from the pump. Move the pump away from the motor shaft. Remove the motor electrical connector and set aside. 4. Remove the three bolts holding the gearbox-motor assemply and pull it out of the tub. 5. Put the assembly on a towelwith shaft up and remove the separator washer from the old clutch that is sitting on the gearbox. Then remove the c-retaining clip from the shaft. 6. Pry out the wire retaining clip from the clutch and pull the old clutch out of the shaft. 7. The clutch kit I ordered came with a plastic brake to clutch cam so I replaced it too, just remove the retainig clip from the brake that is at the bottom of the tub and replaced the part. 8. Installed the new clutch and the retaining clips in reverse order. Replace all parts that came with the kit. The new clutch spring was already in place. 9. Put the assembly back into the tub and re-install all the other items in the same order. It spins good now! 10. While replacing parts, methodically clean all the lint from the motor and from under the machine. The gearbox showed signs of leaking oil so its a question of cost. I left it there until it fails then I'll buy a new machine.

My washer stopped mid-cycle and acted completely dead

  • Customer: Jeff from Ventura, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 9 people found this instruction helpful
I thought the click of the lid switch sounded different so I pulled the top console and tested it for continuity in both positions and found none. When I by-passed the switch the washer started up, so I knew what the problem was. There are four screws involved to remove the console which reveals the lid switch to the left side. There's a single screw for a ground wire but the switch itself is simply snapped in place after disconnecting the wire harness plug (must be done with the lid open btw).

I was lucky to diagnose the problem accurately so that the first thing I suspected turned out to be the problem!

Washer would'nt spin

  • Customer: Dean from Poplar Grove, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 9 people found this instruction helpful
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.

  • Customer: Kevin from Disputanta, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 11 of 18 people found this instruction helpful
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

Somehow or another, the plastic cup inside vanished.

  • Customer: Warren from Lakewood, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 12 people found this instruction helpful
This was a really easy replacement job. All I had to do was twist the old Fabric Softener Dispenser to the left to unlock it, pull it off, and put the replacement on.

top agitator would not operate

  • Customer: Larry from Edgewood, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 9 people found this instruction helpful
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Washer would not wash,spin or drain.

  • Customer: Michael from Covington, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
I thought that the lid switch was the problem why the washer would not perform the drain or spin cycle. I broke the lid switch by moving the wires around. I rigged it so my daughter could use it by screwing a screw in the switch til the new one came in. After a few days, the machine stopped working again as stated above with the motor. I purchased a new Whir-pool washer for her and later found a white wire that connects to the electric motor was burnt around the connector in that only one tiny wire was still attached. I reconnected the wire in the connector and the washer started working again.

Two problems - washer stopped and had to open and close lid several times to restart. Problem 2 - could not get inlet valve to take in hot water.

  • Customer: Harry from Bensalem, PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 9 of 13 people found this instruction helpful
1. Read a repair manual that I bought several years ago for this model. Pictures and notes for removing control panel and back cover of washer were very helpful. Replacing the lid switch was easy as long as you have the lid open when locking it down. The control valve was easy and I swapped out wires one at a time to make sure I didn't swap hot for cold. I then removed valve and locked down new one. Reversing the control panel and back skin were easy with a second set of hands to hold the back panel in place while installing two bottom screws. The parts resolved the problems.

spin cycle was not working / poor

  • Customer: Craig from Plano, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 8 of 11 people found this instruction helpful
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

Washer would not spin a full load.

  • Customer: Ralph from Newbury Park, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 11 people found this instruction helpful
!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.

Tub did not center and seal was hanging out of tub

  • Customer: James from Nelsonville, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 8 of 11 people found this instruction helpful
Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension) then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM

washer would not agitate when lid was closed

  • Customer: Timothy from Saint Louis, MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 7 of 8 people found this instruction helpful
The only tricky part was figuring out how to get to the part. There were only two screws that seemed likely candidates to pop off the control panel (on the back at the corners). Fortunately for me the obvious answer was the right one...the panel lifted up and the new part went in - very easy.

washer would fill but not run

  • Customer: steve from madison, SD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 14 people found this instruction helpful
After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.

Washer would not advance cycle

  • Customer: John from Wauconda, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 8 people found this instruction helpful
Tried different cycles, none advanced. Went online to find exploded view of washer top for removal information. Remove power plug from outlet! Removed a few screws and bolts, pulled plugs and the knob. Look around further instructions were inside. Then removed existing timer for part number specifics. Checked online - timer costs were close but shipping varied quite a bit. PartSelect had the best value. Received package next day. Installed and running within a half hour.
All Instructions for the 11016732500
76-90 of 1,094